Your cart is empty.
Your cart is empty. 1. Modern-design Hand Wheel, polished rim.
2. Design with revolving handle, hand wheel has threaded hole for easy handle assembly.
3. These Hand Wheels are bored to the shaft diameter for their size, and are also tapped for a Removable Handle.
4. Handwheel is good for any application where general or precise adjustments need to be made through a turning mechanism.
5. Widely used in industrial machine tools, such as milling machine, lathes, grinders etc.
6. Install and remove the handle with a hex wrench hex size 5mm.
Specification:
Product Name: Round Hand Wheel
Package Content: 1 x Round Hand Wheel, 1 x Removable Handle
Main Color: Black, Silver Tone
Material: Plastic , Metal
Spoke: 3
Wheel Diameter: 100mm / 4-inch
Center Bore Dimention：12x28mm/ 0.47"x1.1"(D*H)
Wheel Total Height: 47mm / 1.85-inch
Handle Size: 62 x 22mm / 2.44-inch x 0.87-inch(L*Max.D )
Handle Thread Diameter: M6
Handle Thread Length: 12mm/0.47-inch
Hex Width 6mm/0.24-inch
Fixing Thread Hole Size: M6 ( Fixing screws are not included here.)
Scott V Christensen
2025-07-31 11:54:33
When this said plastic, it was a lie. The center is built out of solid aluminum. It was a little tight and I had to work the inside just a little, but it was better quality than I expected. My only complaint was it didn’t have a set screw. Luckily I had one and now Mt table-saw is better than new.
Lee Coulter
2025-07-08 19:28:33
Very sturdy wheel. Well made. I ordered two. No set screws with either and they are metric. Had to ream for half inch rod.
J Scott Boyd
2025-05-15 13:26:45
The screw that attaches this to the console was missing. I went to the hardware store and bought one. It works great now.
FJFs-Son2
2025-05-04 12:28:37
I own a Ryobi DP120 drill press. The crank handle broke (replacement not available) and I used the UXCELL wheel to replace it. The shaft of the table lift rack-and-pinion gear drive is 9/16-inch, so I had to bore a 9/16-inch hole in the metal center piece of the wheel. The set screw in the metal center piece is 6 mm and the wheel did not come with a set screw. I purchased an M6x7mm hex-head screw for this purpose. For the original hand crank, the distance from the shaft center to the crank handle is 2.7". The same distance for the UXCELL wheel is 1.6", so less torque. I help lifting the table up by pushing up a bit on the table. Cranking the table down is not a problem. Much better price for the wheel versus a craftsman equivalent to the RYOBI crank (but both with plastic center).
Chip
2025-05-03 12:28:52
I had to slightly drill out the hole to fit my saw and the handle was sturdy enough to handle the modification. My only beef (and giving it 4 stars instead of 5) is because it did not include the 3mm head set screw which secures the handle to the post it is supposed to turn. How much would it cost to include it in the price? If they added .25 cents to the price it would of been worth it to me instead of going to the hardware store to find it. I gave one star under “sheerness†because the question (after looking up the definition of the word in case I was missing something) has no application to the product in question.
Jason Jischke
2025-04-28 17:44:10
Decent quality for the price. Used to replace the crank on my floor standing Delta drill press. The arbor hole was too small so I did have to bore it out. It also did not come with a set screw, but ironically the one in the original crank fit perfect!
Adam B.
2025-04-20 20:30:19
It is very easy to use this hand wheel as a replacement for the spinner wheel on my AtGames Legends Ultimate arcade cabinet.Not really the intended use, but it fits perfectly, but you'll need two different screw drivers (one hex, one flathead) to switch between the spinner and the wheel. It is easy to swap them in and out as the different games require if you get screw drivers of the right size and length.
Protusmike
2025-03-23 13:34:49
This crank worked, but I had to ream out the inside of the handle because it was out of round and bind up when turning. Also this came without a set screw so had to make a trip to the hardware store and get a metric bolt to lock it in.
Stewart Brooks
2025-01-24 11:54:50
Good Product
Recommended Products
