Enjoy free shipping on orders over $29.99

US Dollar

0 $0.00

Your cart is empty.

uxcell A28 Drive V-Belts 28' Inner Length 13mm Width 8mm Thick JIS Standard A-Section Rubber Drive Transmission Belt

4.5 (11) Write Review

Free shipping on orders over $29.99

$8.29

$ 3 .99 $3.99

In Stock

Qty.:

About this item

Size: Model: A28; Inner Girth: 710mm; Top Width: 13mm; Thickness: 8mm.
Material: It is made of neoprene rubber for resistance to oils, water, and some solvents.
Function: To link two or more rotating shafts to transmit power in a drive system. Even load distribution on belt drives and good wear resistance.
Feature: The trapezoidal shape of the belts cross section wedges into the groove of a similarly shaped sheave or pulley to provide traction and alignment.
Applications: Used for drive systems in the automotive, agricultural, textile, printing, mining, and office equipment industries, ect.

Product Description

How to measure the length of the required belt:

Wrap the rope around the two pulleys
Make a mark
Place the marked rope on a flat surface and use a tape measure to measure the distance between the two marks, which is the inner circumference of the belt

To accurately measure the length of the v-belt, use a belt measuring tool or a soft ruler, not a steel ruler.
The width and thickness of the belt should also be measured to confirm the type of belt.

Installation:

First, loosen the tensioning device, then press the v-belt into the pulley groove by hand, and finally tighten it again.

Notice:

Pay attention to the wear of the belt groove of the v-belt pulley.
Check whether the centerline of the two pulley shafts is parallel, whether the corresponding pulley slots are aligned, and whether there is any skewing phenomenon.
When one v-belt is badly worn and cannot be used, replace all the v-belts at the same time, with the same type and equal length, so that each belt has the same tension.

Maintenance:

Regularly check the v-belt tension, after adjustment still can not meet the specified requirements, must be replaced with a new v-belt.
In use, the operating temperature of the v-belt should not exceed 140°F, do not apply belt grease casually.
Various types of v-belt, should not be coated with rosin or sticky substances, but also to prevent v-belt from oil, butter and gasoline, otherwise, it will corrode the v-belt, and shorten the service life.
V-belt should be stored at a relatively low temperature, with no direct sunlight and no oil and corrosive fumes place.

Application

Lawn Care Equipment

Repair lawn equipment, snow removal machine

General Purpose

Repair band saw, box fan, drilling machine, trimmer

Automotive Repair

Replace the automotive belt



Customer Reviews	66	228	276	107	31	18
Type	B	A	M	K	O	SPZ
Width	16mm	13mm	10mm	8mm	10mm	10mm
Thickness	11mm	9mm	6mm	6mm	6mm	9mm

Joy Erickson

2025-09-05 14:17:03

It fits, and so far hasn't stretched, being used to drive a 6 HP go kart.

Brad Lemanski

2025-08-18 10:53:57

Simple swap out

Customer

2025-07-17 15:35:46

This is a good belt vendor did a good job shipped on time fit my machine well All good

marshall

2025-06-25 17:22:29

I got 2 of these to replace the belts on my craftsman drill press the the old belt numbers indicated they were 30 inches they fit right but we're getting old and had a chip out of one belt got these in and the were so tight I could only install one of them I luckily have a mill I was able to use the outher one for

Kindle Customer

2025-05-29 15:29:09

Fast shipping

wc l.

2025-05-16 16:30:28

appears to be usable dont know longevity but seems well made

Christopher F.

2025-03-18 16:52:39

Seemed to fit just as it should.

Gaylin Goodson

2025-02-28 18:43:16

It didn't fit

Steve

2025-02-24 16:43:22

Price right quality ðŸ‘Œ delivery ðŸ‘Œ next day so far so good needed for snowblower

jerryo

2025-02-01 13:02:37

Nice belt

Joe Taylor

2024-12-29 09:05:50

A-40 V-Belt. Perfect fit for our Delta table saw. Delivered on time, and at a great price. Thank you.

Shopping Cart