I bought these two years before writing this review, in the all stainless steel finish. It's held up perfectly well, and I'm 100% satisfied. You can see in the picture, I bought and installed two, one above the other. The lower rack is holding maybe 90-100 lbs. I weigh about 160 lbs., and easily add my weight to the loaded lower rack. No issue at all with the performance.HOWEVER, THESE ARE NOT STUD WALLS. MY WALLS ARE EXTRUDED RED CLAY MASONRY, WITH CEMENT PLASTER. THE ANCHORS I USED ARE NOT THE ONES PACKED WITH THE UNITS. I bought longer mollies/screws, happened to be rated at 250lbs each. The rack can easily hold plenty of weight on any wood stud wall, but anchoring into masonry always allows heavier loading. It also requires a heavy duty hammer drill and masonry bits.I did install these myself, and I have construction experience.The safety and utility of this unit depends COMPLETELY on the installation. Period. Walls vary a lot - are seldom flat or plumb - and no anchor system works the same everywhere. Folks, this isn't picture hanging - this is a minor construction project. If you're not experienced at getting things level plumb and square, finding studs wiring and pipes in walls, and using things like horseshoe shims, you need to find someone experienced to help - or do this for you.If your walls are drywall over studs, you can't just install the rack anywhere - the anchors have to be in the studs. Studs are softer than masonry, so the same anchor supports less weight in studs, than in masonry. Anchor packages state the load rating for different wall types. Btw, not all interior studs are 16" on center. Also, if you need the rack on a stud wall where the anchor points miss studs, you need to open the wall, set some 2x4 blocking where you want it, repair the wall, before you proceed.Some reviewers complain the supplied anchors are inadequate. This will depend on your particular circumstances. I wanted longer screws to reach the structural masonry under the finishing plaster. My wall is also not plumb. With my shelves level, some anchor points touched the wall, others were 1/4" away. I needed longer anchors for my circumstances. I went to the hardware store, spent less than $5, picked up a set of screws and plastic mollies that are appropriate for my use case. They happened to be load rated for more weight than necessary.The reality is, the supplied anchors probably work safely for most, and are just inadequate for others. My view is, better safe than sorry, and the manufacturer can't possibly evaluate your situation for you. You need to assess your own situation, or have a professional do it for you.Issues you might run into include: Slots and holes in the frame are too snug for the supplied anchors. Solution is simple - use a drill, burrs, files, whatever, to open the holes and slots appropriately. Heads snap off the screws: Yup, especially when the frame slot/hole is too tight, and/or the clutch on the driver is set too hard, the heads can torque off. Anchors too short to reach subwall structure: Go buy some anchors that work for you.In my case, I opened the slots and holes enough to accommodate the beefier anchors.There's a little variation in the mesh squares, but that's no issue, really. The mesh is welded together just fine, it's very strong, and not a visual problem once installed.Again, these units are very strong. You might have to play with the anchoring more than you expected. You might find minor finish niggles, and although I think mine are beautiful, these are not sculptural or decorative. These are important structures, are very fit for purpose, and need to be installed correctly.I super appreciate the value, form, and strength of these Vdomus hanging pot racks. Highly recommended.

I love that this rack can hold 15 pots and pans or whatever else you want to hang from it. Very sturdy and the extra room on top is also a huge plus! We have a very small kitchen with extremely limited cabinet space. This rack was perfect and I was able to hang it above my microwave cart with microwave on it to save so much space. Highly recommend!

My wife got a whole bunch of pots and pans from Vine that took up a ton of space in our cabinets. I installed a pot rack in our old house before we moved that helped immensely with this issue, but obviously didn’t do any good now! So, what is a guy to do?!? I knew we needed a pot rack, but the weight of this set would far exceed any pot rack I previously installed. Then, I found this one with a higher weight capacity and knew this was the one!Now, I had a good idea of where to install it. Nice, clean drywall. Easy peasy. Then my wife chimed in and wanted it above the sink. Only one problem with that - the whole area is covered with tile! This guy has never had the need to drill holes into tile before, so I was pretty gun shy about installing it there. I delayed and delayed installing it because of the unknown. Finally, my wife said to get whatever I needed to do the job. All I needed was a special set of drill bits and a ton of nerve and confidence. Finally, I installed it yesterday and I don’t know the last time I was so wracked with fear. I was beaten, but not down, when my usual route of installing something just would not work. The shelf would not stay where I wanted it on the slick tile. But after taking a bunch of measurements and being super detailed about my preparations before taking the drill to the tile, I was about as confident as I was gonna be. I put some scotch tape on the wall in the areas where the proper alignment would be, where the shelf holes lined up and where the arms went up from the shelf. I made sure things were level and made my marks. Then, the drill hit the tile. The initial crunch of the bit spinning into the tile made me cringe. What made me dang near freak out was the drill bit wasn’t staying exactly lined up where I started, but was really close when it finally bit. Slow and steady now! But the special drill bit did beautifully! Nice, clean holes all the way through. Then, I took my regular drill bit and drilled the hole the rest of the way through the drywall and studs. Anchors went in with some gentle persuasion (and a hammer!) but I got it all ready and put the screws in. Now, time for some real fear - did I get the holes right? Well, after trying out the shelf, I was dead on and lined up perfectly! YES!!!!! After that, drilling the holes for the arms was so much less fear-inducing. Everything worked out better than I thought it would! Satisfied, I set the hooks and smiled with pride at my accomplishment. I had not a single crack in any of the tiles I drilled holes into. And everything lined up perfectly! This morning, my wife put all the pots and pans on the rack and was extremely happy and grateful I was super detailed in my installation of this rack. I gotta admit, that just made my head that much bigger!There was absolutely nothing missing from my pot rack. It came with everything needed to install this rack, but I had to resort to using different anchors as the ones that came with this rack wouldn’t work with the tile. But aside from that, everything else worked great. It was the perfect size for where we ended up installing it and fit everything perfectly.Needless to say, I am pretty happy with how this came out and, dare I saw it, dang proud! It came out way better than I expected. And it is holding everything perfectly. (I honestly was worried the weight would bring it tumbling down!) I honestly couldn’t be happier with this rack and how it came out. The price, the look and the methods the manufacturer gave to install it make this a wonderful pot rack. If you are considering it, it is totally worth it. Just be warned - drilling holes into tile is not for the faint of heart. But with the right research and knowledge, anything is possible! And believe me - when you get it right, you’ll walk just a little taller than before!

I absolutely love this rack, it is big enough for everything I have. It’s also very clean looking and well made.UNFORTUNATELY the hardware that they give you to install the rack with is absolute garbage. Do yourself a favor and get your own anchors and screws for it. They cracked off in the wall, and we ended up having to put putty over the wall and paint, and move the whole rack. Now that it’s up, it’s beautiful.

This is really sturdy & looks great.

This turned out better than I thought! It works perfectly. Holds all the pans and lids on top. Mounting was easy, instructions were easy to follow. Have 2 people to install to make sure its level!

As I age it has made it difficult to reach pots and pans in my crowded kitchen. I am unable to bend down and I can’t rise if I end up on the floor. This rack was the answer for me. I was actually able to install it myself and I’m pleased with the attractive appearance and functionality. I strongly recommend this rack.

This pot rack held multiple cast iron pans, plus a bunch of stainless steel pots and pans. Sturdy, stylish, and useful!

Muy buena calidad, el material de los soportes, rejilla y ganchos son fuertes y está bien armado. Fácil instalación.

Facil de instalar, muy solido y le da un toque muy moderno a la cocina, aparte su capacidad de carga es muy aceptable, me encanto.

Really good quality. Nice and strong. Perfect fit for the space. Easy to hang and use.

Funcional justo.lo que esperaba