Your cart is empty.
Your cart is empty.Product Description
Why choose volport strength adhesive?
Are you worried about the adhesive melting in the hot summer? Are you troubled by the suction disc mount falling off on bumpy roads? This genuine 3M VHB adhesive pad will solve all your problems.
1.Extremely strong adhesive: The size of 4 pieces of 2.2inch (56mm) round replacement 2 face window adhesive stickers perfectly fits the suction cup holder of the driving recorder without any cutting. No need to buy a new suction disk or even a new dash cam or dashboard camera stand, you can simply replace the sticker to restore original functionality and stability.
2.High temperature resistance: Multi-pack high-quality foam adhesive material, which has passed strict extreme high temperature 120℃ (248℉) and cold low temperature tests, can firmly fix the suction cup support under any weather conditions. With this high temperature resistance self adhesive sheet, you can drive with confidence knowing your dash cam will work securely and reliably.
3.No residue: This removable high-bond gel pad leaves no residue and can be easily peeled off when you want to change the position of your driving recorder.
Installation Tips:
1.Loosen the dasdcam suction cup bracket clip lock before installation.
2.Before pasting, you need to completely peel off the remaining old gel spots. A dental floss tool can be used to help remove the old glue.
3.Slide and press evenly to expel the air between the sticker and the dashcamera suction cup
4.Be careful not to touch the adhesive with your hands when tearing off the adhesive protective film.
5.When removing the red protective film, pay attention to pressing the base pad tightly. If the adhesive base pad is lifted with the protective film, you can press it strongly and then tear off the protective film.
6.After installing it on the wind shield, you can slightly pull the suction cup to form a vacuum seal.
7.Please do not use the thick 3m sticker on soft leather, oily, uneven, textured, wet, silicone, rough and other surfaces. Please use it on dry and smooth surfaces such as glass, metal, tiles, etc.
How to install?
1. Wipe the the dash camera suction cup and windshield surface.
2. Peel off the yellow film and Stick the adhesive on the suction cup.
3. Press evenly to make the adhesive and dash cam suction cup fit completely.
4. Peel off the red film and stick it on the windshield.
5. Fix the dash cam suction cup bracket.
6. Apply the auxiliary sticker (wait at least 24 hours before removing).
The diameter of the sun resistant 2sided acrylic vinyl tape is only 56mm, but it can be trimmed and cut into smaller sizes to meet the needs of installing other accessories in daily life.
Stephanie
2025-09-06 12:07:14
I got these to secure a baby camera in my pickup truck back window. It's been installed with these pads for 8 months now without any need to replace them. Easy to use and long lasting. Great product
Mark in Minnesota
2025-08-18 21:09:29
Worked as expected. Just like the OEM adhesive on my dash cam. Easy to cut to size.
Bob Simmons
2025-08-06 16:30:02
Great product easy to use
Winnie
2025-07-18 15:59:56
My phone mounts, no matter what car what surface never stays. But with these, I can always make it work. Can use it for anything needed to be stuck on something. Doesn’t have to be for a phone mount only. If needed to remove it can also be done. Might take a little patience to get it all off. But thats why it does a great job sticking.
Jess B
2025-07-17 11:54:54
This past summer I went to the beach and my car was parked in the sun for days. I have a camera for my baby in the car and the goo on the suction melted on my windshield due to the heat. I know, I knew better than to leave camera in the car but I also hate taking it down and putting it back up. So I needed to find something to replace the other sticky stuff and I found this! I was kind of worried it wouldn't work but it has held up nicely! I waited a few months before I did my review to see how it would hold up. Definitely recommend to replace your old sticky pads if they melt or just dont stick anymore.
JW
2025-07-15 12:45:06
The adhesive material that these are made of-3M VHB (Very High Bond) is actually used in some building construction in place of rivets and welding. It does have a cure time, but once that’s over it is very strong.I got these to hold LED light fixtures to a wall, and they work as promised. There is no comparison with most double sided tape. I’ve never built a building, but I can recommend these for doing what they say they will do.
MarÃa
2025-05-16 17:34:48
muy buen producto el pegamento es muy bueno
Tone Le Lone
2025-04-24 11:09:35
I find my dash mount on the floor of my car at least 3 times a week.This stuff just doesn’t stick.
cecil pickering
2025-03-27 16:40:44
there great now my suction cup doesn't fall the windshield
marlies boost
2025-02-16 16:29:16
Macht was es soll, klebt bombenfest.
Morgans
2025-02-11 11:16:27
Dashcam kept falling off the windscreen so I thought these were worth a try. This is a great product, easy to use (comes with a cleaning tissue as well so you can be sure the windscreen is ready for the sticky product). The protective film comes off quite easily and there are also little strips to attach to the pad in the short term to keep it in places while it sets. Good news is currently it has stayed on no trouble so I am very pleased.
Scott
2025-01-17 12:14:20
Used to stick a suction dashcam mount to a windshield. Works well, even with the center of the suction mount not actually touching the windshield. I followed the instructions and this thing is not coming off without a lot of effort. If I ever have to remove it, I will have to be very careful to not break the windshield as it appears to be stuck that well. I would be tempted to very carefully heat it with a heat gun and then use a plastic scraper to slowly release it from the glass. If that doesn't do it then I would attempt to use a flat razor blade carefully. Consider this as mostly permanent!
SMS
2025-01-02 10:37:33
Die Haftung der 3M-Pads ist sehr gut, wenn man die Klebestelle auch zuvor enfettet.Sehr wichtig ist die genaue Ausrichtung des Klebepads bevor es kontakt mit der Klebestelle hat, denn wenn das Klebepad erstmal angeklebt ist, ist es schwer es wieder abzulösen. Vorallel wenn die Klebestelle gepolstert ist, wie bei vielen Autoamaturenbrettern es der Fall ist. Zum Ablösen kann man sehr vorsichig z.B. ein Messer oder dünnen Spachtel nehmen, da muss man dann aber aufpassen nicht in die Polsterung des Amaturenbrettes zuschneiden. Klebereste kann man anschließend mit einem entsprechendem Lösemittelspry entfernen. Aber Achtung das die Klebestelle auch diesen verträgt!
Recommended Products