Your cart is empty.
Your cart is empty.The toughest truck around gets a new-look hub through distribution. They’re built to take the beatings modified rigs with bigger tires can dish out. With heat treated gears, all metal cap and dial, and corrosion-resistant stainless steel hardware, they’ll shine on the job for years to come. Easy install, turn dial and maintenance but darn hard to break.
Tj W.
2025-08-26 13:29:50
Just what my Jeeps dana 60 needed . High quality parts and super easy installl
AK_Islander
2025-08-25 10:43:16
My factory hubs on my 2008 Ford F350 had simply failed and were so full of plastic parts I just couldn't put another set on my truck. I bought these Warn Hubs and had them on in about 20 minutes! My 4-Wheel drive works flawlessly every time I need it thanks to these First Rate, Top Shelf Hubs! Grew up with Warn hubs on my trucks and still a Huge Fan of Warn Products!!When switching to the Warn Hubs, take some good penetrating oil and one of the original socket head screws to every threaded mounting hole to clean up the threads in the unused holes from the factory hubs. I also added a light coating of grease to both sides of the hub gasket to help keep water out. Great Hubs!!
CHRISTY
2025-07-28 13:26:20
Installed on a Dana 60 auto hub and what an upgrade. Those auto locking hubs are a nightmare and never know if your locked or not until its to late. These make sure your locked. Easy install and everything included. Now i know when i am locked in and can go anywhere!
Glenn S. Capron
2025-07-24 10:02:23
They were super simple to install. Had a couple factory holes that were tight, but a 10-32 tap and some oil and they clean up nicely. Slide right together in under 1.5 hours with basic hand tools. Would have been quicker, but tapping the holes took a bit of time. They look sharp and function smoothly. Reliable also which the ford vacuum ones were not.
Vinyard
2025-06-29 20:10:38
I replaced my drivers side hub about a month ago with another brand. It broke upon installation and I ordered an OEM locking hub but the finish didnt match the passengers side. So I decided to order this set and I could not be more impressed with the quality and finish on these hubs. The design of the finger holds is really nice (I can litteraly turn them with one finger). The bearings inside turn great. There is no plastic cage like the OEM part and other brand I tried. Actually there is no plastic at all. Grease, antiseze, and new screws are included. The warranty is good for the life of your truck (as long as you were the original purchaser of the hubs). I wish I wasnt such a tight wad and spent the cash for these upfront.
Michelle Shaw
2025-06-12 14:10:49
Seem to be ok , not true stainless steel , locking ring is plastic , time will tell if the hold up . Would not buy again , would go with milemarker next time
SEOMike
2025-06-09 17:43:33
It took about 45 minutes for me to install these while sitting in my driveway and required no special tools. My old hub locks were so rotten they were seized solid and the vacuum actuatation had failed. These are a great replacement. They come with a gasket to ensure they are sealed. I used my own copper grease instead of the included anti-seize for the little screws that hold it in. I also used my own Lucas grease to lubricate the hub and threw out their included grease.Since I now have manual locks I now have low range 2WD. My buddy with a dodge truck is super jealous.My only complaint is that there are six screws to hold in the new hub whereas the original had three. How is that a complaint? Well, the three holes which were unused by the factory had become corroded internally which made it difficult to thread in the new screws. I almost rounded out one of the allen heads but with some patience got them all threaded properly. Take it easy, be patient and run the new screws and and out several times to clear out your unused holes and you'll be fine. Probably best to use your original screws in case you round out a cap and have to use vice grips to get it out. Wouldn't want to destroy your new screws.Installed in a 2008 F250. I chose black because I like the way it stands out against the wheels.
James Aaron Plummer
2025-06-07 16:54:51
Very easy to install! The last time I went to use my 4 whee drive on my 2005 Ford F-250 Super Duty, I went to turn the manual locking hub and it came off in my hand. After looking at many other cheaper options I decided to spend a little more and get the WARN ones. I am by far a mechanic but I have learned how to do a lot of my own work on my own vehicle. From opening the box to putting everything up, these hubs only took 45 minutes to install. Instructions were easy to follow. I will also say, yes there are cheaper options out there but you get what you pay for and these are worth the extra money! No plastic here all metal construction!
joe
2025-05-18 10:26:29
Great product, warn us top quality. But the supplier, come on… I clearly ordered the hubs in CHROME. The title said chrome, part number leads to chrome. And the only other option , totally seperate from this, is black. Well they arrived today in gray . Not chrome like I bought . Not black like the other option. Gray.Guess I’ll have mismatched color hubs now since I need to put them in.5* for the product. 3* for the supplier.
Jason Van loo
2025-04-16 11:19:35
Handles look good and are smooth to use
BOB
2025-03-13 20:26:16
Absolutely awesome . Easy to install and they look awesome. And yes , work perfectly.
lucas major
2025-02-26 18:03:15
Great product, 10 minutes to install, they look great and turn very easy even in the freezing cold.
Scott Stokowski
2025-01-28 10:50:31
Super tough hubs, fast delivery,VERY nice price!I rely on this truck so I need QUALITY..All the time..Very satisfied!!’
Recommended Products
