Your cart is empty.
Your cart is empty.Great Product
Thomas Birkemeier
August 23, 2025
I bought these rings to mount my new night vision scope, and they're good little rings. They seem sturdy and well made, but I am a little hesitant about the single knob to tighten to mount them to the rail. Time will tell if they stay put. They seem like they will.
ouchies
August 21, 2025
These are more substantial than regular rings. Very well engineered. Everything tightened as it should. I locktited the 2 center screws on each ring, after tightening down the 4 outers to good torque. Slightly longer than normal rings, so make sure you have the available length free on your scope, first. I mounted this onto a Weaver rail made for a Savage 12, and both items together are excellent. A lot of available space for adjusting the scope. FYI, the scope was a Hawke SF Eclipse 30 mildot - (I have a review for that scope). Hawke make some good scopes for realistic $.
LoneWolf
August 4, 2025
These rings work great and look great on my Vepr 54r.These rings are holding a Primary Arms 4-14x44 Mil Dot scope that is sitting on a Midwest Indurstries side scope mount.I had first bought the low rings but had to send them back cause they were way to low and the scope didnt clear the rear sight of my Vepr 54r..but this High Rings are just right..they are great quality rings :)
A Concerned Buyer
June 29, 2025
Great value rings. It could handle FAL 308 with ease and have not lose zero for several training sections. Highly recommended.
Blaik
June 18, 2025
I bought these rings for my Remington 700 .308 to mount my 10-40x56 Sightmark riflescope.Pros: These rings look awesome. They are very solid and fit well with the squared crossbars. They worked perfectly with my scope, which clears the barrel by a perfect 1/8" with the caps installed or 1/4" without (barrel is a Remington 700 #7 Varmint Contour cut to 20" from recoil lug and measures .860" diameter @ muzzle).Cons: I had hoped for a nicer fit to the rail, but it's decent for the price. Also, upon opening these rings I decided that I wanted to check the fit of just the bottom half of one of the rings to my scope, so I slipped the bottom half of one of the rings on and it didn't just slide right in. The ring (both of them actually) were not quite cut round to fit the contour of the scope tube, and were machined quite roughly on the inside. So, having just slipped the ring on basically just to see how it looked, I removed the bottom half of the ring and some of my scope's coating with it. So, I would say make sure you run a lapping bar through these rings prior to putting a scope anywhere near them at all, unless you want a nice cut in the finish of your scope, like mine.
CharlesS
May 9, 2025
Weaver is still producing a quality product. Mounted easily to my rifle rail system and I did not need to do any lapping or additional tweeking to get them aligned. Shot a tight group and easily adjusted my scope. The scope has maintained the zero and the mounts have not come loose.I have not tried removing and remounting to compare alignment.
Kolin Kiefer
May 7, 2025
These rings are a steal at the price.They are used to hold my Leupold on a Remington 700,300 win. mag. They hold the scope well at 300 yds.You'll like them on your scope. They are cosmetically beautiful as they are functional.Worth every dollar. You will be estatic about them.Kolin Kiefer
W.
May 4, 2025
I'm pretty new to the shooting sport, but I expected these to fit a picatinny rail tighter than they do. There is only one screw that spans the width of the ring and clamps it to the rail, and the body of that screw is square to fit in the groves on the rail, but there is a LOT of slop in there. When placed on the rail I can slide the ring forward back by about a tenth, maybe a quarter, of an inch. I didn't think they were supposed to have that much play in them, but maybe I am wrong or got the wrong thing. However when the screw is tightened (I used 40 inch pounds) with the ring pushed all the way forward it seems to grip the rail securely enough.
Gregg R
March 21, 2025
These are decent rings. Solid construction. Not made off shore. As good as or better than a brand name scope line for quarter the price. I have 3 sets.
shane
March 10, 2025
Great Weaver rings, looks great, top quality. The package says for a 44mm objective optics but I fit a 50mm optic with a low profile weaver rail and it still a good amount of clearance between the barrel and the objective bell of the optic. Oh and another pro of the product... THEIR MADE IN THE U.S.A. NOT CHINA!
Jn
March 8, 2025
Saddle height is 12 mm. The package specifies up to 44mm objective. If you have a bigger scope, you may need to look elsewhere. Otherwise decent rings.In spite of the package specifications, I was able to use these with a 56 mm Trijicon on my Sako A7.
Alex
January 11, 2025
Weaver keeps to be great value for the money
charles
December 1, 2024
solid align well. as per any other needed fitting for bed.
Recommended Products
$57.50
$ 24 .99 $24.99