Your cart is empty.
Your cart is empty.Cut moldings, picture frames, Table edges and more in a beautiful double Roman Ogee design. Two flute carbide cutters with ball bearing guide. 1/2" Shank. 3/4" Cutter height, 9/16" Cutter depth.
wally tucker
2025-09-03 12:23:28
Looks and performs like a high dollar production router bit. Needed a nice profile on a cabinet project. Have used it for edges only a few times. Love the profile.
T. Fagan
2025-07-28 13:12:34
When the cheap plastic frame on a large mirror broke, my daughter wanted a new wood frame for it. Using some leftover and rather knotty 2x6 lumber, we ripped it and fashioned a functional but rather boring-looking frame. On seeing the YONICO Classical Roman Ogee Router Bit (1/2" shank) while browsing on Amazon, I decided to give it a try to give it a bit of character..The Classical Roman Ogee bit looked great coming out of the package and it went well through approximately 21 feet, inside and outside the frame, through typical wood and knots alike (see photo for example). Yes, it took a quick sanding with the sander at the cut-to-frame interfaces, but the routed portion took only a very light hand-sanding with 320 grit sandpaper to get it ready for priming and finish painting. The bit cut uniformly well and evenly, and looked the same at the end as it did at the start. I give this one 5* and a highly recommended rating.
RUADOGWALKER
2025-07-25 09:27:06
YoNico makes nice router bits for the money and there really isn’t much to complain about with this router bit. It’s just not a white side.
Thomas W Troutman
2025-07-04 19:56:35
Cutter bit is made nicely and cuts well.
Nimedic
2025-05-19 12:53:02
I purchased this while I was making a couple of small wooden boxes. I had been using a Bosch Roman Ogee bit with the same dimensions but, it was at least 5 years old and beginning to burn the wood and had a few minor chips in it. Although I've been woodworking for a few decades I purchased this bit thinking that a bit with the same dimensions and name would create the same profile, when I ran a test on a scrap piece of wood, they looked the same but, I was wrong. The bit cuts as smoothly as would be expected of a new router bit but there's a slight detail that didn't match the Bosch bit.I certainly can't take anything away from the quality of the YONICO bit because it performs quite well and, I would purchase their router bits again. The issue I had was my fault.
Mike Fleming
2025-05-01 11:56:32
Done several practice runs with this bit. Works fine for me.I clean mine with nylon bristle brush after use.I used on 3/4†edge.The second picture I only used part of the bit profile.
Ol' Hesty
2025-04-19 11:44:06
I used this bit on several pieces of standard dimensional, pine lumber. Also used it on old stock very old pine, which is much harder. The blades held up flawlessly. Coating is smooth and without imperfection.If you’re considering Freud, Whiteside, or Amana, I’d say to give Yonico bits a go first to determine if it will satisfy your expectations.. If your running hundreds of meters of board daily, and you’re making cabinets then you will want Freud four blade bits.
Stephen Ortado
2025-04-16 18:03:19
Exactly correct item , fast delivery.
Stephen Keough
2025-04-08 13:00:51
Arrived early. Works great. The price is excellent. Could not get this product in any of my local stores
Guillermo Pardo
2025-03-20 13:48:43
Justo lo que necesitaba para las molduras de mis puertas.
Randall S.
2025-02-14 16:46:05
Fast delivery. Bit works very well if you make 2 passes. Didn't heat up much either. Very sharp. I'm very happy with it.
Fernando
2025-02-02 16:14:05
Excelente calidad
Lukou
2025-01-28 16:42:47
Pour ce que j'en fais, cela répond parfaitement à mes attentes. Les produits Yonico ne valent certainement pas les Freud mais pour une fraction du prix, vous pouvez vous faire plaisir.
Recommended Products
