Your cart is empty.
Your cart is empty.Product Description
The control A-Arm bushing mainly mounts on car suspension and steering joints to absorb road bumps, control the amount of movement in the joints and reduce noise and vibration.
Since the bushings have been exposed to over-heat, salt or lubricants for a long time or just been over stressed from movements and weights loads, they can wear out. When you found things happen above, you need to replace a new set of bushing for your smooth usage and comfortable experience. Bushings from Tutor Auto is worth your trust.
THESE 24PCS SHORT BUSHINGS COMPATIBLE WITH:
- 2010-2014 Polaris Ranger 400
- 2002-2004 Polaris Ranger 425
- 1999-2013 Polaris Ranger 500
- 2011-2013 Polaris Ranger Crew 500
- 2013 Polaris Ranger Crew 500 Midsize
- 2006-2008 Polaris Ranger 700
- 2008-2009 Polaris Ranger Crew 700
- 2005-2009 Polaris Ranger XP 700
- 2009-2016 Polaris Ranger 800
- 2010-2014 Polaris Ranger Crew 800
- 2012 Polaris Ranger XP 800
- 2013-2014 Polaris Ranger 800 Midsize
- 2011-2014 Polaris Ranger 900
- 2012-2014 Polaris Ranger Crew 900
- 2010-2019 Polaris Ranger EV
- 2008-2010 Polaris Sportsman 300
- 1999-2000 Polaris Sportsman 335
- 2001-2014 Polaris Sportsman 400
- 2006-2020 Polaris Sportsman 450
- 1996-2017 Polaris Sportsman 500
- 2014 Polaris Sportsman 550
- 2008-2020 Polaris Sportsman 570
- 2015-2019 Polaris Sportsman SP 570
- 2020 Polaris Sportsman Touring 570
- 2015-2020 Polaris Sportsman X2 570
- 2003-2005 Polaris Sportsman 600
- 2002-2007 Polaris Sportsman 700
- 2005-2014 Polaris Sportsman 800
Richard H. Franklin Jr
2025-09-03 15:03:00
The product is not made to the correct flange thickness causing the control arm to slide back and forth. I was able to find a washer for the inside positions to make up the thickness and maintain the castor angle. The install works fine now. However, I recommend updating your description.
Braxton
2025-08-21 15:15:24
got exactly what I needed and bushings are still holding up on my hunting rig
bethany finley
2025-08-19 14:36:56
They seem to be doing ok so far
Graderman
2025-08-18 18:02:19
Shoulder is a little too short. I had to use two flat washers to take up the space . Was a 2009 Polaris ranger 500
Customer
2025-08-04 09:38:56
Great price,fast shipping . Bought for Polaris ranger xp 700 (2008). Shoulder width of new bushing about .080†narrower than factory width (.278†factory verse this replacement .198â€) times 2 bushings equals.160†loose movement effecting suspension “castor angle†Not good
Robbie J. Florance
2025-08-03 14:33:17
Polaris obviously designed this suspenion part to fail in a rather short amount of time. Plastic bearings in such a machine is going to fail for sure in a relatively short time. Steel sealed Roller bearings would last many many years longer. The price at the Polaris dealer was nuts so I bought these. They worked fine. Got extras knowing what will happen...
phil scarfo
2025-05-30 14:22:05
These bushings were easy to install. They are very hard material and I worry about them busting in cold weather. There was not a bushing left not even a piece to compare hardness. I was lucky none of the metal parts were worn out. They were very easy to install it only too about 1 1/2 hours to install them all. I hope they last.
Terry
2025-05-09 11:22:16
Two small for 2004 Polaris ranger 500
Lisa Matthews
2025-04-14 17:49:23
Haven't used these.....yet. But with 2 Polaris ATVs and a Polaris side x side, no doubt they will be needed in the future. They look exactly like what's on my bike now so i don't see having any issues with them
steven stavrou
2025-02-20 10:41:24
good product
Recommended Products