Your cart is empty.
Your cart is empty.
Specification:
1. Easy to disassemble no flaring tool required.
2. This fitting is made of brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability.
3. Fitting body and 1 nuts for splicing damaged hose.
4.Very easliy to install.
Product matching
This adapter is one kind of repair kit, can suit for plastic hose such PU, PVC,PE or Rubber hose etc. And please know that the OD of rubber hose and PU hose is different, and our rubber repair fitting have a
This fitting can have a good sealing than clamps.
Victor Wren
2025-08-26 13:33:07
I bought this to use with a TeeJet 6466 sprayer handle on my ATV-mounted spraying rig. I hate hose clamps for things that I have to handle. Not only do they catch on everything, but half the time I end up with pesticide leaks all over my hands. The Solo backpack sprayers use a kind of compression fitting that is not only secure and watertight, but completely smooth. It's a bit bulky, though, as it uses a 3/4" GHT (garden hose) fitting. I have looked long and hard for a compression fitting that I can use with my spray handles, so that I can get rid of hose clamps. Most fittings require multiple parts, and you're on your own where dimensions are concerned. This compression fitting has only two parts (most have at least four), and is much less bulky.HOWEVER: This fitting is tight enough that it will only work with a certain thickness of hose. It will not work with rubber hose, or PVC air hose, as they are too thick, making it impossible to work the nut over them. As it happens, it works perfectly with the 3/8" braided hose from Sprayer Depot. The picture on the Sprayer Depot website makes the hose look chunkier than it actually is. It's rated for 225PSI, and I rarely spray over 60PSI, so it should serve my needs very well.When assembling it, make sure that the hose is cut perfectly square, and sticking out past the end of the nut, so that the hose seats completely to the bottom of the barb, before the nut tightens down. I suspect that people who complained about it coming apart either had VERY thin hose, or did not get the hose all the way onto the barb. I cannot see how this could come apart, otherwise.The kit comes with a couple of pieces of Teflon tape, which is rather silly, as that is easily obtained almost anywhere (and most people doing plumbing work already have at least a few spools of it sitting around.) But I suppose if you're in an area of the world where Teflon tape is a rare commodity, this could be a useful addition.
Customer
2025-08-25 15:11:32
I have some cheap hose that needed ends found these to try and they worked perfect no leaks at a great price easy to Install will definitely buy again
Michael N.
2025-08-15 15:11:50
Too small for the 3/8†ID rubber hose on the reel. My fault.
DHW
2025-07-01 15:05:06
Well made and claims to be for a rubber hose. My air hose is bigger than the nut and had to be shaved to fit. Not ideal, should state the ID of the nut.
DANIEL F BOESL
2025-06-23 11:00:31
This is used to repair air hose and is as described by seller
PeteBF
2025-06-19 13:16:35
As seems to be the norm, part is machined improperly. 0.078" out of spec. You might be able to make it work on brand new hose but you wouldn't need to repair brand new hose. Per usual, some engineer/designer wasn't thinking. Save yourself some money and aggravation and just buy a kit at your local hardware store.
House of Jensens
2025-06-13 13:57:10
I bought these because it seemed to have a much better ID than the trash connectors that came on my 1/4" polyurethane hose from Amazon. Turns out it does, I put my calipers on it and its not 1/4" ID but its close.So putting this on 1/4" polyurethane hose is freaking hard. I had my adapter in a vice, heated the hose with a heat gun and then used vice grips on the lock down nut and barely got it to start threading in, after minutes of trying and more heat and silicone lube. Then it sucks down fine and will never come apart.They are 100% brass, which is good to know.For the second adapter I took a very small step bit and bored out the leading edge of the hole on the lock down nut so it would allow it to slide up and grab threads just a little before really snuggung down on the hose. Turns out it was still really hard to install with my hands(couldn't get to my vice in this position), and I could have bored it some more. But I finally got it on.Combine these with Milton type M fittings everywhere and you have a very small OD, light weight hose with enough CFM for nearly any air tool. I love it!
Hayden Cain
2025-05-12 14:58:47
Good
gerry demers
2025-02-21 18:46:39
it was perfect for my plastic line to the pipe thread
Michael Ouellet
2025-02-04 10:55:38
Good
dgirard61
2025-01-16 19:53:44
j ai utilisé ce produit pour réparé une hose a air 1/4 le fitting de compagnie etait briséavec ces fitting jai reussi la réparation mais au debut ca ne fonctionnait pas un coup la hose installé sur le fitting il etait impossible d installé la bague de retenu en place jai été obligé de reduire la hose avec un peu de chaleur pour pouvoir vissé les deux connection ensemble ca fonctionné
Recommended Products
