Your cart is empty.
Your cart is empty.Product Description
Highlights
Fork Seal Driver Tool 33mm-45mm
Replacing fork seals is an essential process to maintain your bike, and here is THE tool you need to get the job done!
When you first notice the sign of oil on the stanchion tube's legs when the forks travel, it is time to change your fork seal.
If the leak is allowed, the oil will continue to run down the back of the fork leg, onto the brake calipers.
Eventually the fork will run out of oil, seizing the bushing surfaces which allow the fork halves to slide, eventually lock up the front end.
Comes with storage case.
Instructions
- Take apart the fork ...
- Slide the old seal off
- Inspect the stanchion for blemishes
- Oil the inner surface of the new seal with fresh fork oil
- Slip the seal over the top of the stanchion and slide it down to the slider.
- Adjust the tool’s plastic fitting to match the size of the seal by loosening the three cross head screws and decreasing or increasing the diameter.
- Press the adapters against the seal, slide the driver tool up and down several times until seal is pushed into the slider
Fork Seal Driver
Designed for easy installation of most fork seals.
Manufactured from carbon steel, split design with weighted body.
Works on most conventional or inverted forks.
Three jaw chuck may create pressure points.
- Won't damage your new fork seals during installations
- The weight of the tool presses the seal evenly into the fork tube
- Adjustable size, no need to buy specific size for each individual bike
- The tool is designed to install OEM lip style seals
Easy Use
This fork seal driver tool has a two-piece design. The bottom plastic piece directly contacts the seal, it is shaped in a way that press the seal into the recess of the fork tube. The Top metal piece, is made of heavy metal, it acts like a slide hammer to smack the seal into position. With a few up and downs motion, the seal will be properly seated in the fork tube.
Check out our store for more motorcycle tools and parts!
John R. Ridley
2025-09-06 12:19:35
Works great, put in my fork seals and dust seals very easily. Glad not to have to buy several different sizes for my different bikes. Probably not best choice for shops but for DIYers doing a fork seal once or twice a year it's good.
Farm & Fabrication
2025-08-22 12:53:47
I did a comparison on Amazon. I got this, the Motion Pro, and a cheap plastic one.This fork seal set actually does real well for the $$. If You're a Dad with kids who ride or you and your buddies want one kit to cover a couple bikes, this is the business!
Flet
2025-07-28 11:08:05
I have several bikes and lucky for me they all have different fork sizes! I bought the properly sized motion pro driver for my first bike and it's worth the money, if you only have one set of forks, just get the right tool for the job. However, I decided to cheap out and give this a try for my 2 smaller forks (37mm and 43mm). So far so good doing the 37mm set. To get the inner bushing seated on a convention fork you need to use the old bushing and the seal washer on top of it, that creates a nice flat surface for this driver to push against. Use a good grease (Race Tech ultra-slick) and throw some heat onto the outer fork leg and everything goes together pretty easily. My only complaint is that the the 'hammer' part is pretty giant. It's obviously the same size used for all forks so on a 37mm it's pretty floppy. It does have a coating on it so not worried about marring the legs but would be nice if it was better sized for the forks its designed to work on.
John T
2025-05-15 16:40:36
I got this set of fork seal drivers to make the job of installing new fork seals easier during a rebuild of my '85 Honda CB650SC Nighthawk. The bike doesn't matter - this set will do the trick on any forks within the specified range in the product description. These were effective, easy to use, and performed exactly as I had needed and expected them to be. I am glad that I have them, as I will be using them again from time to time with my own bikes (and probably for a friend here & there). No complaints, no concerns - these are worth their weight in gold. Recommended.
Dwayne Evans
2025-05-13 12:01:14
It came early, is very heavy and sturdy. It is a great tool that my husband will be able to use for years to come. Very simple tool to use and a great value for the money. And I'm a woman so I like good packaging and this one is great good sturdy case and thank you note with their info. Highly recommend.
RJ
2025-03-28 11:57:41
Used to put seals in a Harley Davidson heritage softail and it worked great. Glad I bought it and I would definitely recommend
TatamGreen
2025-02-26 17:13:11
Havent used them yet but the product seems durable and came in a nice case
Dirtbike Derek
2024-12-27 16:33:12
Building bikes over 35 years.This works great.You squeeze the teeth by hand it diesnt fit into the slammer.Then you slam the bushings in first hitting on the washer.Then install your seal.Creates less force on your seal.Works awesome.If you had a problem then you suck at mechanics.lol
Recommended Products