Your cart is empty.
Your cart is empty.
Compatible Part Numbers:
6800S312, AVR-C5KW, AVR3-5KW, AVR5-1F, AVR-CD294, MXR250V470uF, Rubycon250V470uF, KMH250V470uF, KMG250V470uF, 31700-Z22-A31, 31700-ZD1-A41, 31700-ZP1-J71, 31700-ZS4-003, 32350-ZA0-D01, 32350-ZB4-A41, 32350-ZB4-A42, 21066-2069, 21066-2074, YF1-89610-28-00, YF1-89640-28-00, YF1-89670-28-01
Specifications:
New AVR 6.5KW
AVR for Generator
For 4KW - 6.5KW at 160V-260V
Maximum Output: DC 90V 3.5A(1 Blue positive 1 Yellow negative Wire Connected to Carbon Brush)
Excitation Voltage: 90V ~ 120V.
Sampling voltage ( feedback voltage):18V
Frequency: 50/60Hz.
AC Voltage Output: 160V ~ 260V for 240V output
Auto Voltage Adjusting Accuracy: ≤ ±5%.
Maximum Temperature Rise: 130C or 266F.
Continuous Working Time: ≥ 20 Hours.
5.5 inches hole to hole
Fitments:
Replacement for Elemax: SH4000, SH5000, SH6000 & SH7000
Replacement for Sawafuji: SH4600EX, SH5300EX, SH6500EXS & SH7600EX
Replacement for Yamaha: EDL6500S & EDL6500S2
Replacement for Kawasaki: GE2900A, GE3200A, GE4000AS, GE4300A, GE4500AS, GE5000AS, PP4000 & PP6000
Replacement for Honda: EB3500, EB3800, EB5000, EB6500, EC6500, EG3500, EG5000, EL5000, EM3500, EM3800, EM5000, EM6000, EM6500, EN5000, EP3800, EP5000, ES6500, EX3300S, EX4500S, EX5500, EZ3500 & EZ5000
Replacement for Subaru: Husky 6250
Max
2025-08-30 13:55:44
Worked like a charmThanks so much for the great service
J.P.B.
2025-08-27 18:38:52
Bolt / plug in replacement worked well. Except for the unmarked brush connectors. Had a 50/50 chance of correct connection and whoops, no output. Voltmeter check and had the blue/yellow reversed. Blue + . 117vac & 234ac no load. 110 & 220 loaded. My only concern is the lack of a heat sink on the power transistor. One inch square of thin aluminum should suffice.
Ron
2025-08-20 16:47:41
No issues installing and performed as expected.
Max
2025-08-12 11:35:23
Worked like a charmThanks so much for the great service
J.P.B.
2025-08-06 17:44:09
Bolt / plug in replacement worked well. Except for the unmarked brush connectors. Had a 50/50 chance of correct connection and whoops, no output. Voltmeter check and had the blue/yellow reversed. Blue + . 117vac & 234ac no load. 110 & 220 loaded. My only concern is the lack of a heat sink on the power transistor. One inch square of thin aluminum should suffice.
Ron
2025-07-09 14:46:12
No issues installing and performed as expected.
bludaim
2025-06-25 17:02:54
item as described , on time delivery. will purchase from this vendor again.
Joan
2025-06-19 19:37:11
I bought this regulator to replace the one on my generator. I am a contractor, and when I use my generator, it runs 8hrs. a day every day for weeks at a time. I bought this one because I felt the cheaper ones would not be as robust. Installed in generator along with new brushes. Fired it up and checked voltages, all good.Recently got another job where need the generator daily. Ran fine for a week. Then compressor starts having problems kicking on and saws start struggling. Get my meter out and find I'm only getting 93 volts at all outlets. Check brushes, still good. Put in regulator purchased elsewhere. Right back up to 120v.If you want to have reliable generator, do not by this part.
Billy Morton
2025-04-27 18:34:53
💪ðŸ½
Ross M.
2025-04-19 10:45:18
Works as it should
Patricia S.
2025-04-06 19:28:25
First AVR came with the big capacitor in the back installed crooked so it hit the case of the generator and could not be bolted in the case. I thought this was likely a manufacturing defect, and a fluke so I ordered same item as replacement and I was correct, the replacement was assembled correctly.Please note: blue wire is + and installed on left side of brushes, terminal closest to armature.Unfortunately the voltage setting was way off, only had I think 200v, I must have turned the adjustment pot 12 full turns to obtain 240/122v.Note 2) you must turn screw counter clockwise to increase voltage, this is opposite what I saw in other posts.I have only tested with 1500w so I sure hope this holds up when neededI will try another brand next time, although I tend to think they all all made the same.
bludaim
2025-04-01 15:45:21
item as described , on time delivery. will purchase from this vendor again.
Joan
2025-03-03 17:42:28
I bought this regulator to replace the one on my generator. I am a contractor, and when I use my generator, it runs 8hrs. a day every day for weeks at a time. I bought this one because I felt the cheaper ones would not be as robust. Installed in generator along with new brushes. Fired it up and checked voltages, all good.Recently got another job where need the generator daily. Ran fine for a week. Then compressor starts having problems kicking on and saws start struggling. Get my meter out and find I'm only getting 93 volts at all outlets. Check brushes, still good. Put in regulator purchased elsewhere. Right back up to 120v.If you want to have reliable generator, do not by this part.
Billy Morton
2025-02-21 17:41:41
💪ðŸ½
Ross M.
2025-02-20 21:02:53
Works as it should
Patricia S.
2025-01-22 11:56:00
First AVR came with the big capacitor in the back installed crooked so it hit the case of the generator and could not be bolted in the case. I thought this was likely a manufacturing defect, and a fluke so I ordered same item as replacement and I was correct, the replacement was assembled correctly.Please note: blue wire is + and installed on left side of brushes, terminal closest to armature.Unfortunately the voltage setting was way off, only had I think 200v, I must have turned the adjustment pot 12 full turns to obtain 240/122v.Note 2) you must turn screw counter clockwise to increase voltage, this is opposite what I saw in other posts.I have only tested with 1500w so I sure hope this holds up when neededI will try another brand next time, although I tend to think they all all made the same.
Recommended Products
$129.00
$ 55 .99 $55.99