Your cart is empty.
Your cart is empty.Product Description
Stable mounting design
This kickstand has mounting points on chainstay and seatstay ,this design effectively increases the stability after installation.
Height adjustable foot
By pressing the spring button on the foot ,you could adjust the kickstand’s height easily to fit your bike size.
Frame diameter compatiblity
The kickstand could fit on bike frame size 7-25mm(TOP) ,13-28mm(Bottom),and is suitable for oval and rectangular chain stays frame.
Installation angle adjustable
The kickstand could fit on most bike frames with different angles between chainstay and seatstay.
Easy to install
You just need to tighten 4 bolts to mount the kickstand to your bike’s frame by using a 5mm Allen Key (not included).
Ready to go
Wish you a fun ride !
Chris W
August 2, 2025
I bought this for my daughter’s 26†MTB (with rim breaks), which didn’t come with a kickstand. It fit well and the length can be adjusted in seconds. The clamps are padded, and the kickstand you mount it carefully and correctly, it won’t damage the paint. It’s sturdy enough for rough-housing kids.The one thing I can’t say if it will fit a bike with disk breaks.
R. D. Lombardo
July 31, 2025
The unit is very well made and easy to install. Very sturdy and works very well. My only complaint is that it didn't come with the Alyn wrench needed to install it. Fortunately, I had the correct size in my toolbox. Caution, when lining up the bolts make sure you have the threads lined up properly. Do not force as you will strip the threads on the unit. Fortunately, I watched a video where the fellow installing the unit stripped the threads and I used caution. All went well and I have a very nice kick stand installed.
Doctor567
July 19, 2025
Just barely big enough for my Norco Storm w/ 27.5" wheels, and it's the biggest one I could find. Took a few tries to get to grab correctly onto the upper frame member, but it was doable. After getting it on correctly, I am pleased with how sturdy it holds the bike up. The height-adjustable end seems like a good idea, but unfortunately it has a side effect of occasionally falling off. Easy enough to put back on, but eventually I know I will lose it. I am thinking about epoxying it in place for a permanent setting.
Melissa mom
June 1, 2025
My daughter’s bike had a traditional kickstand that had plastic by the center screw (terrible design). When the stand broke, replacing it in the same place didn’t seem like a good idea. We purchased this rear kickstand just to try it. Although a bit intimidating when opening the package (prior to installing it), it actually was very simple to put on the bike. The adjustable stand was very easy to set, and wide base supported the bike well. Frankly, I thought the plastic structure and simple height adjustment we’re going to brake and the stand seemed weak. After using it (Note: Teenager), it’s held up great. Far better than both her old one (and another center mount I bought from a store). Her friends seem to have issues constantly knocking over their bikes, but hers has help up great.
Hans W. Gasterland
May 31, 2025
Fast and easy to install. Works like it should. Easy to adjust height so that Bike doesn’t fall over.
Craig W.
May 1, 2025
Just installed this kickstand on my Schwinn Varsity 1250 700c hybrid bicycle. Only thing to take into consideration before purchasing is that this kickstand might not mount properly with some disc brake systems. For me personality, this wasn't an issue since this bike has cantilever brakes. My last pic shows me holding a 5mm Allen key (the most commonly used size on bicycles) somewhat close to where a disc brake rotor would sit so you can see there's little clearance. Depending on frame shape and angle of the tubes on it, i could see the bracing arm and brake caliper lining up, which could also make mounting difficult.It's the perfect kickstand for my needs. Mounted in just minutes, looks good and far more sturdy then my last. I ride a lot, carry a bag with necessities, like a few tools if anything breaks, etc, so the added support def makes me satisfied.Installation tip:When installing, tighten all of the bolts until they are just snug. Doing that before you fully tighten any down will seat the mount where it fits the best, basically pulling itself in line to where it should be. Then, kinda like you would do with bolts that hold your handlebars to the stem, tighten them down evenly, alternating between each bolt a little at a time, until they are tightened fully.Hope this helps!Craig
Happy Camper
April 29, 2025
Does fit with disk brake. Was able to use on the horizon bar. The vertical bar clamp was hitting into the disk.
Koro
April 22, 2025
I'm usually not compelled enough to write reviews; however, this stand is an absolute pile of garbage.My first one I ordered, the threads stripped without much effort. I thought it was either low quality or I torqued too hard. I didn't think much further about it and got a replacement.My second one, I was much more careful screwing in the screws. After it was on, I tried putting the kickstand up and down in succession. After a few times of doing it, I noticed that the kickstand started swaying a bit back and forth going from the up and down positions until, eventually, it needed to be screwed in again. I gave it several tries before thinking each time was a fluke, but it kept happening. Once I removed it from my bike, that's when I saw the scratches. My bike was absolutely scratched from this thing swaying back and forth!So not only does this product not actually stand up too well (no pun intended) to use, it'll absolutely scratch up your bike doing it.I'm not sure how the other comments are even recommending this product, but I definitely don't. Biker beware!
Marc A. Laplante
March 17, 2025
a bike stand can go either way- be flimsy and lead to the bike toppling over, or over the top- heavy and cumbersome.This model hits right up the centre- plus is easy to install and adjust to the ideal height for your bike.highly recommend this.
Tom reviews
March 11, 2025
Great value for money, easy to fit if you have common sense, holds my ebike up perfectly.Honestly if you struggle fitting this or cross the threads seriously consider not having kids as the future depends on simple tasks.Use locktite and just nip it up, easy
internet173
February 26, 2025
- - - Ich verstehe nicht wie man für solch einen Fahrradständer mehr als 2 Sterne geben kann. DER VERSTELLBARE TEIL RUTSCHT EINFACH DURCH SOBALD DAS RAD ABGESTELLT WIRD. Die Metallklammer die sich am Aluminumständer verkrallen soll ist abgerundet und die Schlitze im Ständer sind nicht genau ausgearbeitet. Das kann so beim besten Willen nicht halten. Ich hatte mir den Fahrradständer für das Fahrrad extra wegen der vielen guten Bewertungen gekauft. ICH WÜRDE DEN FAHRRADSTÄNDER NICHT WIEDER KAUFEN. ---
Barrie
January 16, 2025
Bought this for my e-bike and it works fine on a flat surface. 4/5 but the top bolt stripped so I had to supply my own ? Must be an awful cheap bolt to strip after only one tighten and it wasn't even very tight ? I hope the bottom extender stays strong also .... time will tell...
PH
December 30, 2024
Badly designed adjuster. The mechanism is poorly made with a tiny piece of plastic and a spring. Mine arrived broken. Even if it was not broken. I can only imagin e this lasting a few days. Also if any weight is lent on the stand the adjuster slips and the locking mechanism breaks. I expoxy resined the foot onto the bottom of the stand and saved it going into landfill.
Recommended Products