Your cart is empty.
Your cart is empty.Product Description
Product Key Features
Why Brilliance Laser Inks?
- Shake & spray application
- Easy to apply. Easy to wash off.
- Anti-Clog Technology
- Permanent Mark
- Quick to dry
- Marks on various metals
- Up to 4,000 square inch of coverage
- Works with CO2 and Fiber Laser Nd:YAG Laser Systems
Laser marking made easy with our Aerosol Spray (in 2 oz & 12 oz)
Exceptionally adaptable laser marking inks to create high quality permanent mark on a various metal surfaces.
With just a shake and a spray, conveniently make a permanent mark on your metal substrate with our aerosol spray. It comes in two sizes: 2 oz. and 12 oz to fit your needs.
Note that this product does not include any alcohol in the package. Below application tutorial is for instructional purposes only.
How To Apply Aerosols
Step 1
Clean the substrate with denatured alcohol so it's free of any dirt and oil.
Shake the bottle well for approximately 2 minutes to make sure that all contents are mixed.
Step 2
Hold the bottle at 45° degrees and spray 6-8 inches from the substrate surface using left to right motion. Apply a thin coat as long as you do not see through the surface.
Wait for the mixture to dry completely or use a hair dryer to dry it in seconds.
Step 3
Adjust and focus your laser settings according to the material and make your mark!
You may refer to the table below on Suggested Laser Machine Settings.
Step 4
No waiting time needed to wash off! Rinse with tap water or wipe with a wet cloth.
Voila! You now have a permanent on a finished product.
MikeM
2025-08-21 14:44:54
Works as advertised, just soooo expensive!
Frank
2025-08-16 17:34:04
The first shipment arrived and the can was defective. I called customer service and they immediately sent a replacement.Great customer service!!!!!!
Anthony Harris
2025-06-11 09:40:57
Works as described. Takes a little learning but looks great when you apply it correctly to correct material.
Customer
2025-05-28 15:14:27
For the price I was expecting it to be a bit larger amount. But I should have read the description better. We were laser engraving names on zippo lighters and as I said it worked well on stainless steel.
Thomas R.
2025-05-07 12:28:03
Did not spray out of can.
A. B.
2025-03-07 10:14:56
Laser marking spray is wildly expensive, and this is no exception - the 2oz can is only small enough for one or two projects, so be very conscious of whether you might ever want more product before ordering it. (There's a can with 6x as much product available for less than 2x the price, for example, and Brilliance also sells powders and liquids that can be more cost effective than the aerosols.) If you're looking for a tester before committing, this might be a good solution, but otherwise I'd steer you towards one of the larger containers.This is an unusual product in the world of laser marking chemicals because it cures to a kind of rust-like, burned copper tone color. (It's definitely not cherry red.) This would be good if you wanted to add a faux weathered engraving onto something, in particular - I could see lots of art or themed entertainment uses for this spray. I think it's less useful for general purpose marking, as in many applications the black spray will be more legible and will 'pop' more cleanly when engraved.Like the other Brilliance products I've tried, this engraves well and produces clean results on my 45W Muse CO2 laser. The spray is certainly easy to apply and it's a convenient form factor, so it is worth a little bit of a price premium. I just think the asking price for the 2oz can is a little too high, and suggest going for the 12oz if you do want an aerosol.
mike clarkson
2025-02-19 12:36:04
For the price I paid I thought it was the full 12oz size instead of the 2 oz
stephen Lynch
2024-12-23 20:25:12
Brilliance products always work pretty darn well if you follow directions.I do not do a lot of red metal, but I do do a lot of stainless, and it works well to leave a brownish copper colored marking which is substantially darker than it would be without it.I had to play around with settings to kind of find My "sweet spot, then it was smooth sailing..The product works pretty well with both a Co2 laser, and a fiber laser.
Karlin
2024-12-11 18:22:24
Is pretty expensive but lasts for a long time. Makes a permanent mark, does take a little bit to figure out the best laser parameters though.
Recommended Products