Your cart is empty.
Your cart is empty.Product Description
Crank Pulley Install Tool 551141 for GM LS/LS1 LS2 LS3 LS4 LSX LSA LS6 LQ4 LQ9 Engines 1997-2023 # 2 Sets of Ball Bearings
This LS Harmonic balancer Tool is perfect for your Camaro, Corvette, Trans Am, GTO, G8, LS Truck, or LS powered street rod.
- High Grade 12.9 Steel Threaded Rod
- Heightened flange nut
- Galvanized steel nuts and washers
- Anti-rust and corrosion resistance
- ONE more set of thrust ball bearing included
Compatible with:
- For all GM LS and GM LT series engines 1997-up (Gen 3th, Gen 4th, and Gen 5th)
- For Chevy Camaro Corvette, Trans Am, GTO G8, LS Truck or LS Power Road Signs
Not Suitable For:
- Except Gen 2 LT1 5.7 engines (1992-1997)
This LS Harmonic balancer Tool is made of high-quality alloy structural steel material.
With durable black finish, anti-rust and corrosion resistance.
FINCTION:
Help thread into the crankshaft and push the crankshaft pulley into position.
The thrust bearing set is much safer and more convenient than pulls on the balancer with a bolt.
ADVICE:
Applying lube to the inside of the balancer helps with installation and saves stress on the tool, which makes the installing a breeze.
You will get
A longer(7.48in) threaded rod
It's long enough to start installing the harmonic balancer.
A lengthened flange nut
TWO SETS OF THRUST BALL BEARINGS!!
A thickened washer
Yes, you read that right!!
You will get 2 sets of these ball bearings. A great value!!
- Help you do the job much easier
- Save your time and strength
- One more in need
J. Ferrell
2025-09-01 13:37:06
We had to replace the oil pump in a 2008 Chevy Silverado, 5.3L and discovered we needed this tool or a longer bolt to put the harmonic balancer back on. After looking at reviews we pulled the trigger on this one. 20.00 shipped overnight. Great! Well it turned out it really was great! No issues - the bearings made it easy to turn. Putting the factory harmonic balancer on was very easy. No crushed bearings or screwed up threads. Not sure why those folks had such issues. So for us - this worked great. Hope I never have to use it again!! lol But if I do, I have it. Oh and if you're doing this job, remember to buy a new harmonic balancer bolt. They're cheap. Good luck getting that 250 lb ft of torque on it. I recommend you buy the fly wheel locking tool to help with that.
Tino G
2025-08-31 17:57:49
I've been working on my 2008 chevrolet colorado and needed a install tool for the harmonic balancer. I went down to the local auto store and rented a kit. When I got home I found that the unit was too short to thread into the crankshaft so I had to run back to town and return it.I got back home and started looking at tools on Amazon and came across this one. The reviews were all over the place. Some negative and other were positive so I decided I would order it and see what I could do. It came in the next day as expected. I went out and put some motor oil on the threads and threaded it into the crankshaft as far as it would go and then backed it out a full turn. I also put dome motor oil on the crankshaft and the balancer. I placed the balancer on the crankshaft and then the installation bearings and nut. I held the thread rod with a 10mm and used a open end wrench to slowly push the balancer on. It went on without any problem. I wish I could use it again but if the timing chain replacement fixes the issue with my truck I should be good to go.
James
2025-08-17 18:40:57
We tried the old school way of lightly tapping the old harmonic balancer on and it not work, it fell and broke. So we bought a new one and then this tool and it pushed it in with no effort. Just buy the tool. Like other reviews it did break the bearing of the tool installing it but it came with an extra so it’s worth it
GIOVANNI GONZALEZ
2025-07-22 20:35:06
there are no dislikes about this tool, its perfect for the money, does the job well and makes installing harmonic balancers on GM LS1 a breeze, easiest tool you'll ever use to install harmonic balancers. on the downside i lost 2 ball bearings on first try, seems like the crown that holds ball bearings in place need to be manufactured better, but it doesn't stops the tool from doing its job, i recommend, don't know what other engines this tool will work on .
Kindle Customer
2025-07-15 17:00:12
Used 1 time and thrust bearing fell apart
Customer
2025-05-14 16:48:14
Be sure to switch to the oe bolt before you run it in completely.. run it in with no problem, used some assembly lube on stud into crank and stud to nut.. once it got snug, I went another ½ turn to tighten and heard a crack sound.. upon removal I found that the outer groove washer had cracked in four places and fell apart.. so run you harmonic balancer on till you can use the oe bolt to tighten..
DANIEL S SWARTOUT
2025-05-03 09:18:46
Very well made and quality. Great value.
Brian
2025-04-06 10:02:53
Worked perfectly for installing a LS harmonic balancer! Recommend purchasing this for even a novice mechanic. Price couldn’t have been any better, bonus!
Kristina
2025-03-06 13:05:28
Worked perfect, with the small bearings it turned in nice and smooth.
Nelson
2025-03-02 20:55:28
No especifica la medida del tornillo!
john coderre
2025-02-09 13:01:31
Worked perfect with no effort,great tool for the price
AMB
2025-01-23 18:20:46
Good tool function well and did the job. But managed to break it.
Recommended Products