Your cart is empty.
Your cart is empty.
Exhaust Manifold Repair Clamp Kit
Location on motor: Drivers Rear, Passenger Front
Fits: 1999-Current 4.8 β 5.3 β 6.0 β 6.2 liter V8 GM Trucks, Sierra, Silverado, G-Series Vans, Pontiac G8, Envoy V8, Hummer, GM SUVs (including Escalade & Denali & Tahoe)
Also fitsοΌ V8 versions of Buick Rainier, Isuzu NPR & Isuzu NPR HD (4.8, 5.3 or 6.0). GMC Savana Van 2002 β 2012 with 5.3 & 4.8 and 2002 to present with 6.0.
Bracket
Bolts
Spacer
Easy instructions
Approximate installation time: 1/2 hour.
The bracket is made from 1/4 inch thick plate steel that has been stamp formed and gusset welded.
It is fastened to the cylinder head using existing factory pre-drilled holes in the side of the cylinder head. The bolts included with this kit are 10mm in diameter.
THESE BRACKETS ARE VERY HEAVY DUTY AND MADE TO LAST !!
William
2025-08-01 14:23:39
Very hard to install. Fits like it should. Works great. Definitely worth it. Installation is a pain because vehicle manufacturers like to put the engine under the dash practically.
Jose gutierrez
2025-07-11 15:52:05
Sucks doing the job but works really well I suggest doing it from under the truck with a 16in ratchet wrench less struggle after everything is bolted on just make sure to tighten it donΓ’β¬β’t be scared make sure it seals the leak definitely a 10/10 weΓ’β¬β’ll see how it holds up after a while
BussaBuss
2025-06-15 11:14:42
Not easy to install, but once itΓ’β¬β’s on it works flawlessly. I recommend having someone help due to the extremely tight space which only allows for your 16mm wrench and nothing else. I was underneath the truck working from the bottom while my wife (sheΓ’β¬β’s so handy!) aligned from the topΓ’β¬Β¦definitely a team effort. All 3 bolts will be a slow and tedious process to tighten due to the very limited space. I did not remove the powder coating from the threads as itΓ’β¬β’ll help keep it in place and from rusting. I do recommend removing the coating from the bolt head that pushes the manifold so as to fit your wrench onto it much easier.
Lindsey.laine
2025-05-31 12:02:29
I had bought this product came in on time. Great part, however was missing hardware.I reached out to see if they could just send me replacement hardware. Seller told me to reach out to Amazon Customer service. Amazon customer service said they would not be able to assist and that I could only return the item. Now I have truck on the lift tying up a service bay.
D
2025-02-20 17:43:27
Other than it being rather hard to install, the item worked as well as can be expected. It is much better than not having it, the manifold has stopped leaking.
wlbartman
2025-01-06 16:43:03
Super easy to install. Front 2 bolts on the right exhaust manifold are gone and I was getting an annoying ticking sound. This bracket fixed the problem until I have time to replace the bolts.
JJ
2025-01-01 17:01:23
Installed on 07 Silverado 4.8L right front. Fit perfectly. All I had to do was grind the paint off around one of the mounting holes because I had 2 grounds land there and I also used a wire brush to remove the paint off of the bolt that pushed against the manifold. The paint was extremely thick and wouldn't allow movement to tighten it. Once the paint was gone I could turn it easily. Once tight, it sealed the manifold perfectly. I also used a little Loctite blue as added insurance on the pusher bolt. 20 min vs an all day pain in the neck project is definitely worth the $20 I spent for this. I wish all jobs were this easy.
Scott
2024-11-21 17:45:19
This is a much more affordable and easier option i would say. Works on my 2006 6.0 Cadillac Escalade. Tight fit and not too easy to install. But is do-able. Worth the $20 I would say. Holding up well so far and made well too. Good ship time and not mad at this purchase at all.
Recommended Products
