Your cart is empty.
Your cart is empty. JMTAAT Solid Aluminum Front Inner Fender Liners for 2007-2019 Jeep Wrangler JK 4WD
Super heavy duty aluminum construction fits for 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 Jeep Wrangler JK JKU 4WD
Full coverage for total protection, keeps mud and debris out of engine bay. The integrated design upgrade the overall appearance of your Wrangler.
Easy DIY installation, keep your mounting 10mm bolts to work with these. Drilling may be required to fit better.
Improves the look of inner-fender. Available in line grained raw aluminum. Easy access to your Jeep's shocks, Easy to inspect and adjust.
Package Includes: fender liner×4 Pcs | All necessary hardware you see on our pictures are included. Instruction is NOT included!!!!
J
July 28, 2025
Great value! Was worried at first but got these and they fit very well. I painted them with bed liner. Easy install as well.
Patrick
July 18, 2025
I got these because the price point and material finally hit the right spot. The reviews were also really helpful so I knew what to expect. Because the price was low, I also picked up a rivet nut tool at harbor freight for this project and what turned out to be an other $40 of rivet nuts and m-5 screws because my wife wanted black hardware. I am satisfied with the product. But, on my 2008 Jeep Rubicon unlimited the produce is about 1/4 inch too short on the top/front corners. The gap is hardly noticeable, but I know it's there. Also on the drivers side, lower corner the cover seems like it needs another attachment point, but it's too short and there isn't enough metal on the body lip. If tapped the cover rattles on the body/frame, I did not hear it on the road though. I will probably just cut a little extension tab so that I can screw it down.Installation was not "easy." It required a little bit of skill as well as the right type of drill bits for the install. Make sure you have the right sizes and type. The aluminum product is easy to drill, gut the jeep, namely the radiator mount needs something harder than the easy to find "titanium." (I will be looking for a set of cobalt bits for this type of project." A helper would have been nice but I was able to finish the project in about 3 hours. I had to drill some extra holes in different locations due to previous modifications I had made.I will update this for long term after we run some trails too.
Justin
July 1, 2025
First off, they could have included a couple self-tappers to complete the install and deleted the mystery round plate that does absolutely nothing(wtf?). It fits pretty well and might require a little bending which is pretty easy to do by hand. I honestly expected to have to grind some edges to avoid rubbing, but didn’t have to. Looks great when installed and fits pretty good. I picked these because they didn’t have a cheesy design which is apparently hard to find on Amazon. Definitely could have used some washer for the tiny bolts. They included so many extra nuts that I used those as “washers†to prevent the bolts from pushing through. You’ll need a few self tappers and some washers to complete install.
Allen
April 29, 2025
I installed these on my 2011 JK to make spark plug change easy. The hardware that came with them is unusable for my purposes. Between the two panels I used threaded inserts on the front panel and a bolt with a flange head to hold the rear section to it. I have also trimmed out around the spring pocket to stop the rattle that was happening when hitting bumps.
NickByDesign
March 19, 2025
10 minute install, great quality too!! Would buy again if I ever need to.
Connor Logan
March 5, 2025
Yes they’re cheap, but I wouldn’t spend a dime on these. Look fine and do the job once they’re on but awful instructions and no necessary hardware. I bought these to replace previous liners so I didn’t have oem hardware. Overall terrible just spend a little more on something better
Heidi
February 9, 2025
These look great once installed. They so take some time to install since the holes to mount do not line up correctly. Took about 3 hours to get them installed. Overall I'm happy with the look and quality just expect to do a little extra work to get these puppies on you jeep.
Customer
February 5, 2025
Drivers side installed in about 10 minutes the passenger took a little longer as I had to reroute my winch wires. Also the passenger side needed a little persuasion with a dead blow at the front. Was a body man by trade for 20 years and I’m used to things not being perfect. I think any complaints are from people that don’t understand that jeeps are mass produced and so are these inner fender wells by a different company. I would not hesitate to buy these again especially if you don’t want the silly designs that are cut into other companies products.
Recommended Products
