Your cart is empty.
Your cart is empty.Gates Corporation is a leading manufacturer of application-specific fluid power and power transmission solutions. At Gates, we are driven to push the boundaries of materials science to engineer products that continually exceed expectations.
Jeff
September 4, 2025
This belt replaced the worn out ac belt. It fit and worked well using the gates tool to install it.
Glenn
August 20, 2025
I installed this on my 08 Subaru Impreza to replace the factory one. Works great and the tool made the job replacing it easy. Definitely saved money by doing it myself than going to the dealership to have it done.You have to cut the old belt out, so make sure you have all the proper tools before you do, or else you'll be S.O.L.
M. Pujols
August 5, 2025
Just as good if not better than oem.
Velo Buff
August 2, 2025
Fit my 2010 2.5 non-turbo Forester just great!My old belt didn't show visible signs of wear (see pic) but since I was already replacing the squeaky alternator belt I figure why not - my Scooby has 75,000 miles so it's overdue for new belts anyway, in theory. I'm not sure I believe the Gates video when they show you how to use the tool and claim that the AC stretch belt is designed to wear away at the same rate as your regular serpentine belt. The AC belt, while it does spin as much and is shorter than the serpentine belt, only has load on it when the AC compressor's clutch is engaged. Meh.The Gates 91031 tool is a must when replacing the belt. I posted a review there but basically, you should watch the video a few times on how to use the tool before going under the hood and while you're replacing the belt.My stomach was a little queasy as I cut the old belt off like it showed in the video. It was the hottest day of the summer and if this didn't work then I'd have been out of AC! Fortunately, its so easy a caveman can do it.
domenic
July 28, 2025
Worked good price
H. Ho
July 27, 2025
The belt is made very well with a quality not unlike any of Gates products. I've put about 10,000 miles on it so far and it still looks good from a previous removal and re-installation. It's still too soon to talk about wear and such, but from what I see so far, its a good fit. I'm trying to offset the bad reviews because, although I understand the switch to a stretch fit belt is a DIY-unfriendly change, it was Subaru's decision to use these types of belts. The belt itself is made well and serves its purpose. I DO have my gripes about the use of stretch-fit belts that I'll address below.First off, the old tensioner pulley design on quite a few of the older model cars had (in my opinion) a bad tensioner design. For those who have the old tensioners, they were set to apply tension at an ANGLE rather perpendicular to the belt. This would cause unnecessary strain to the tensioner and subsequently they wind up with customers who get damaged tensioners. Instead of redesigning one that applies tension perpendicularly (90 degrees) to the belt, Subaru decides to slap on these stretch fit belts. Now you are left with a few options on getting an A/C belt on your car.Option 1: There are mounting points on some of the new engines which could be mounted with the old tensioners, just do some research to find the right tensioner and belt and you can convert to the older but easier and cheaper (in the long run) way to replace your beltOption 2: Buy a proper install tool. There are "universal" ones that wont work. Some tools require the A/C belt to be on the outer part of the crank pulley. My 08 Impreza has the AC belt on the engine side of the pulley.Option 3: It is possible to get the belt on and off with a bit of muscle and with a 1" inch width nylon strap (about 3 or 4 feet of it will do). Just use the strap to pull the belt towards you as you rotate your crank to "walk" the belt off the AC pulley. Once the strap gets caught between the AC pulley and belt, just use the other part of the strap to pull on the belt to continue walking it off the AC. Getting a new belt on is more of a challenge, but can be done in the same fashion. Having someone to turn the crank as you walk the belt back ON can make this easier. You'll have to pull hard and get enough initial tension so that the belt can hold on to the pulley's instead of slipping. I've done this successfully on my own with no damage and no problems, it was just a pain to find a method that works. If you are REPLACING a belt you can just cut the old one off. I have re-used my OEM belt when I installed a new crank pulley and put over 70,000 miles on the re-used belt with no problems and installed a new belt at my 90k mark. The old belt didn't even show any unordinary wear.
The Kolbe Family
July 23, 2025
Like others, I thought it would be too small, but it stretches to fit as advertised and you should really get the installation tool or see if you can borrow one from a shop, friend, or auto-parts store. I bought this one and used youtube to figure out the technique.
Lou Hdez
June 18, 2025
I installed this belt on my 2010 Subaru Forester. Easy to install, good quality and great youtube support videos that make you confident on the installation as it featured a similar engine than mine. you need Gates 91031 Engine Tool a to make this truly a snap to install. I would highly recommend this product.
dramenard
June 12, 2025
As described
Mek
June 10, 2025
It’s a stretch belt so make sure you have an installer tool. Worked great at a great price.
Customer
May 11, 2025
Original OEM belt on my car. What else can I say.
Patrick m
March 23, 2025
Beaucoup moins chez que les voleurs de Subaru
Jordan Robb
February 13, 2025
No issues, quality product.
Recommended Products
