Your cart is empty.
Your cart is empty.
Features:
Brand New and Never used Parts.
Made by Premium Quality Material.
Extremely Durable Aftermarket Part.
Easy to install and prefect replacement for original parts.
Specifications:
Watts: 306
Length: 3.25"
Width: 3/8" Rod With 1" Fins
Connectors: Male Spades
Replaces part numbers: 1-10-06620, 3-20-06783, 3-20-677200.
Fitment
This 306 Watt igniter is compatible with all automatic ignition Harman stoves. Was formally a 15 Fin.
Absolute 43-TC
Accentra 52i
Accentra
Accentra Insert
Advance
Allure 50
P35i
P43
P61A
P68
XXV
Troubleshooting Igniters:
Igniter failure can be verified on one of three ways.
1. start your stove and visually look for the orange glow;
2. physically feel around in the burn pot after the stove has been on for a few minutes to “feel” for heat being generated.
3. Use a DMM (Digital Multi-Meter). Gain access to the igniter and remove it from the stove or insert. With the igniter removed from the stove, you will need to look over the part to find the rated watts.
If your Ohms reading is within 10%, more or less than the rating (46Ω +/-10%), it’s good. If the igniter has a “contained short” or a short within itself and not grounding out, your Ohms reading will be very low...usually in the single digits. Generally, you cannot have a faulty igniter with too high of a resistance reading unless an igniter is installed that is way out of spec. It’s usually good to look at the part itself for the watts rating.
LeRoy Krebs
2025-09-05 11:40:47
Fits perfect, well built and easy to install!
Adam
2025-08-18 17:34:45
Pretty easy installation - plenty of YouTube videos out there but basically a matter of pulling the old igniter out from under the burn pot (held on by 2 screws), gently pulling it out (likely have to remove back cover by temp controller unit to loosen the wires so you can pull the igniter out - the wires go to the back of the unit). Once the igniter is out, work it out if it’s housing but make sure to notice the orientation of it so it’s easy to reinstall with the new igniter. Pull the wires from the back of the unit to tighten them up a bit, put the igniter housing back into place, screw it back in, pull the wires fairly tight again from the back of the pellet stove, put the back cover in place again, screw it in, and fire it up!Hope the igniter lasts, just had it in for a few hours but the stove started right up and swapping it out too a total of around 20 min, would have been faster but it took advantage of having the cover off so I cleaned the cobwebs out, etc.
Bob
2025-06-24 15:29:54
Have bought before, matches the appearance of OEM . May not last quite as long as OEM. But price is way better. Easy to change. Fast ship !
Don H
2025-05-19 11:45:03
Easy to install, fits a Harman P43 perfectly and my stove is firing normally again and we're warm.
Crunk
2025-05-15 18:15:18
I purchased this to replace the igniter on a harman Advance. Initial impression from its physical appearance is that it is well built; besides having the fiberglass lined cables, there is an extra fiberglass layer closest to the igniter to provide extra protection. The original unit that I had included 15 fins while this replacement had 16, so I was initially worried that it wouldn't fit in the housing, but it did. It is just a little snug but there is enough clearance if you line it up flush and push it in.Immediately started the pellets way quicker than my old one did before failing, so it works well. Now we'll see how long it lasts....
David Gross
2025-04-26 14:38:32
Awesome product
DK
2025-04-11 18:15:28
The original igniter on my brand new Harman P61 lasted less than 1 year. It was under warranty and Harman sent a tech out from a local store to install a new igniter which lasted about 14 years. If you see the picture of my old igniter had 13 fins and it looks like for some reason the tech who installed it had pulled off the heat resistant fabric when he installed it. I do not know why he did this, I remember when he did it he was very shifty and would always try blocking me looking at the igniter and the back of the stove. Perhaps the pull off the heat resistant fabric sleeve so the igniter fails earlier and they get an additional call out.This one was easy to replace, has more fins, I tested the resistance before I installed it and it was perfectly within specifications. It lit the fire within a few minutes.
T Coe
2025-03-25 11:59:42
The weather warmed up and only used it once since purchase. Definitely solved the problem as original igniter finally died after nearly 10 years. Hoping this one lasts as long. It was a perfect fit. Didn’t want one with more fins as I thought it might clog quicker and need cleaning more often. Price was very inexpensive.
Customer
2025-03-16 09:18:39
Was easy to install and worked perfectly
G. Zwicker
2025-03-11 10:33:15
I've had a Harman P61a pellet stove for 15 years. The original ignitor lasted 10 years. The OEM replacement that I paid $170.00 cdn for lasted 2 years. The non OEM that I bought after that for $100.00 lasted 1 year. Basically gave up on ignitors after that. Then I seen this one on Amazon. It cost $30.00. I thought it was cheap enough to take a chance. It had a fire going in under 5 minutes. If it lasts a year I'll be happy. I'll update this review if anything changes.In conclusion, I have a Harman P61a stove and this is an exact replacement. Works perfectly so far so I'd recommend this if you need a new ignitor.
Paul T.
2025-02-13 10:25:21
Unit was a direct fit, despite having 17 fins as opposed to the OEM's 15. Got a flame less than 4 minutes after start-up. No idea about long-term reliability. Will report back if issues appears.
Customer
2025-02-04 21:17:25
This has been working well for its first week. I have probably ignited the stove 5 times and noticed no issues. I have a Harman Accentra 2 pellet stove and this igniter had more fins than the original. I had to bend the fins on each end inwards to make it fit within the holder but otherwise its working great so far.
bob
2025-01-19 10:59:07
This was a perfect fit for my Harman Pellett stove and was so easy to install and fire up.
Recommended Products
