Your cart is empty.
Your cart is empty.Extra mounts + spare partsA grab bag of mounts and spare parts.Less ThanbRGreater ThanLess ThanbRGreater ThanCompatibilityLess ThanbRGreater ThanHERO12 BlackLess ThanbRGreater ThanHERO11 BlackLess ThanbRGreater ThanHERO11 Black MiniHERO10 BlackMAXHERO9 BlackLess ThanbRGreater ThanHERO8 BlackLess ThanbRGreater ThanHERO7 BlackLess ThanbRGreater ThanHERO6 BlackLess ThanbRGreater ThanHERO5 BlackLess ThanbRGreater ThanHERO5 Session
Just Josh
2025-09-04 11:46:46
This is a nice little set of various pieces and spare parts that is handy to keep around when you’re trying to build that perfect GoPro mount. The set includes a curved mounting base with 3M VHB tape, a flat mounting base with 3M VHB tape, a standard height mount, an extended height mount, a pivot arm that consists of two pieces, two small thumbscrews, a standard length thumbscrew, and a shorter thumbscrew.If you combine the curved mounting base, the standard height mount, and the normal thumbscrew you have a duplicate of what usually comes with a GoPro camera. Then you’re left with the flat mounting base, the higher mount, and the pivot arm. Combining those parts gives you a nice raised arm that can pivot both back and forth and side to side so you can get a level shot even if you need to mount the base at an angle.The set includes a shorter thumbscrew that can be used when you don’t want the thumbscrew to extend beyond the edge of the camera. This is useful if you are tilting the camera at a 90 degree side angle as it allows a full tilt without the thumbscrew impacting the main part of the mount. The only downside is that the tolerance is very tight and it will be hard to fully tighten the thumbscrew so you may need to use a screwdriver to tighten it down if you need it to be completely locked in place.I mainly got this set in order to get the extended height mount and the pivoting arm. Combining these two things will raise your GoPro about 3 inches off the mounting surface and provide a different perspective versus the standard low mount. I’m using a GoPro mount in my car and the standard mount results in video that doesn’t give a good view of what’s directly in front of the car. Using this kit allows me to raise the camera up higher and angle it down a bit to get more of the ground in front of the car in the frame.All of the pieces seem very sturdy. I’d much rather pay a little more for the genuine GoPro accessories versus having a cheap knockoff fail at a bad time. Highly recommended set if you’d like to add some versatility to your setup!
Bear and Angela
2025-07-11 12:45:49
These are a great set of the typical mounts you want for your GoPro. Great backups for other vehicles and applications I need them for with the great quality you expect from GoPro
Gary P.
2025-07-06 10:50:37
The collection had just what I wanted at a great price.
Walt Garcia
2025-06-19 16:29:11
Ordered for motorcycle helmet. Curved piece was too curved for the front of my helmet, using the flat piece.Pros: GoPro OEM mounts and pieces are stronger than knock off plastic. I've broken enough to know. Mounts have the rubber anti-vibration/lock grommet that actually works. Not scared of base flying off at highway speeds due to 3M adhesive foam. Perfect angle and height on my motorcycle helmet(HJC CL-17).Cons: Even with the extended height mount I still could not get the angle that I wanted on my helmet. I had to use the extender piece, which I wish was instead a longer single piece. However, the current 90 degree turn angles on the arms are fine since it includes two and acts like one long piece. I do wish that they would have included flush screws instead of the T screws or the longer screws so would not have to see that much coming off of the mount. I also wish that the foam on GoPro bases that have the adhesive would be thicker, so it would be easier to mount on slightly curved surfaces. However, that could have been easily negated by doubling up the adhesive foam and pressing harder. I could not since the adhesive on all the bases came pre-adhered to so of them, and I didn't have any spare.Final Thoughts:Not sure if the old j-hook mount would have given me a better angle, because I wanted the camera at that exact place and that angle. Might take some heat to the base to soften up the adhesive and take it off in order to re-adhere it with two foam pads for extra security. Overall, a very useful kit if you plan on mounting to helmets or other odd angles, or even if you only need a little bit of elevation.
Luis Tamayo
2025-06-13 18:31:58
Perfect, arrived on time
Joe
2025-06-03 15:35:44
All you need and a must have kit for novice and enthusiasts. Nothing like original equipment that works.
HikerBiker
2025-05-24 10:45:38
I've bought non-GoPro mounting hardware before because you can get twice as much stuff for the same money. But it's just not as good. The cheap knockoff mounts are made of inferior, squishy plastic. The tolerances are poor and don't line up correctly.Buy your mounting hardware from GoPro. It's super rigid and everything slots in where it's supposed to and doesn't flop about. You can crank up the tension without worrying about cracking some cheap piece of plastic. It's clearly higher quality.This kit comes with flat and curved adhesive pads, low and high profile snaps, and a 90 degree mount. It includes long and short bolts. I bought it to attach my drone's controller to a GoPro mount on my bike's aerobars. I will be using the curved adhesive pad and the low profile snap. Works a treat.
Austin Lara
2025-05-15 13:01:37
The media could not be loaded.
Customer
2025-05-12 11:09:18
Nice product
Daniel Zitlalpopoca
2025-03-25 16:16:58
Excelente, la presentación, la función, todo es muy buena ya que es original y más barata que en tiendas departamentales
Oh! Bi-One Ken-o-Bi
2025-03-21 11:39:50
N'achetez pas des sous-marques Chinoises, privilégiez les accessoires originaux GoPro.Les quelques euros demander en plus sont réellement justifiés !
Jose Miguel
2025-01-28 15:01:01
Ahora sà engancha bien
Chris Müller
2025-01-25 10:07:46
Alles was ich bis jetzt daran befestigt habe, hällt!
Recommended Products
