Graspur Single ATV Gun & Bow Rack - Model ATV1

Easy to install, fit my front rack perfectly! I’ve traveled with my rifle and my crossbow with no problems! Great addition to my Yamaha Grizzly

Very pleased with this product. It was very inexpensive so I had my doubts. I set it up on my 4-wheeler to accommodate my crossbow but it works well for my rifle as well.Highly recommended

I bought these for carrying gardening implements, such as my Husqvarna string trimmer on my Arctic Cat 400. Because it is very long (and most of the things I'm likely to carry are long), I oriented them front-to-back by putting one mount on the front rack and one on the rear. My rack is 3/4" round tubing. The mounting is easy enough with the U-bolts, but unfortunately there's not enough contact area, and the plastic of the base is not rigid enough to really get it tight. When I encountered even the slightest bump, the Graspur would slip and the string trimmer would start to lean over to the side. I had to ride one-handed and hold onto it to keep the mount from falling over and dumping my string trimmer.The fact that these are offset is a blessing and a curse. The good part is that it gives me more room, so that I can leave these mounted and still have room for my spray tank on the rear rack. Also it gives me a little bit more leg room on the right. But the offset also gives it a greater mechanical advantage, increasing the twisting force on the U-bolt over bumps. The U-bolt could only be tightened a certain amount. Tightening it more just led to the ears on the bottom of the Graspur rack bending down. The plastic is slippery, so it's no help it keeping it from rotating on the rack. Not to mention that, as it rotates, the u-bolt is destroying the paint on your rack (not a concern for me, as the paint on my 20-year-old Arctic Cat racks is already history). As is, the u-bolt did not work for me. It might have better success on larger diameter tubes, or square tubes, but from what I've seen, 3/4" round tubing is very common on ATV racks. These might be adequate for people carrying something lighter, like fishing poles, bows or rifles. But I'm just as likely to be carrying a 20 pound breaker bar or post hole digger.Graspur has made elongated holes where the U-bolt goes through, to allow for swiveling the rack on the tube. I have no use for this feature, and I can only imagine it would be useful where racks don't have tubing at 90º to the axis of the vehicle. Because they wanted this pivoting ability, they had to make the bottom of the Graspur flat (also to accommodate square tubing), which doesn't help grip the tube. In making it as universal as possible, they sacrificed much of its holding ability.What it needed to make it really useful was a better clamping system, with more support for the ears, and more contact area on the tubing of the rack. That would allow the mount to live up to the strength of the upper part. I cut some chunks of 1"x2.5"x1.25" 6061 aluminum, and I machined a set of proper holders for it, fitted to my particular rack. These are now rock-solid, and cannot be moved. Also, the flat mounting provides support for the plastic ears on the base of the Graspur, keeping them from bending down as the bolts are tightened.Obviously this is only a solution for people who have a machine shop. If I'd hired someone to machine these pieces, they would have been far more expensive than the Graspur itself. I think that anybody who has a 3D printer could produce something very similar, custom-sized to their rack, and it would be a vast improvement on the holding ability of the U-bolt, even in plastic. Some extra support would also keep the ears of the Graspur from bending down as the bolts are tightened.The rubber bands and the little nubs on the inside do a pretty good job of holding, but I can't help but think they're not going to survive very long in the Texas sun, so when I'm not using them, I take them off and store them in the Cat's trunk. I've bought some extras, as I expect them to get broken and/or lost out in the fields (there are replacements available on Amazon, both from Graspur and 3rd-party vendors).

I got these because they are offset. It works perfectly to fit on the baby stroller that I found. I have to get another set now that I know it works so I can carry my father in laws shotgun also.

I have only had it on the ATV for 1 day so far, but took it for a test ride with my shotgun secured in the rack... and it worked great. I believe it will work well, and hold up for years. Easy installation... the bars on my rack are quite a bit smaller than the mounting brackets, so I made them 'bigger' by wrapping a little hockey tape on them... worked great.

Good quality product. Unnecessarily difficult to install and tedious to remove. If the ability to take on and off is important to you, I'd recommend another option. Components seem very sturdy and would last well.

No more beating your gun up while heading to the secret spot! This will keep your gun safe but easy to get to fast! I went years with my 45-70 slung over my back but I know now I will never do that again! Mounts easy and holds my gun sturdy!

I purchased this unit to hold my crossbow, shotgun, and muzzleloader on my Grizzly XTR. So far with going over the very rocky terrain of north jersey it has worked like a charm! Make sure whether you are using the mount or not you keep the rubber latches secured so they dont come off.To be noted, do NOT over tighten for one, second if you bump into them they will move slightly. Just keep an eye open when transporting your goods.

Works great

Por ser de muchísima utilidad lo recomiendo

I tested it on my bike and it stays in one place👍

Fits perfectly on the back basket of his Electric Bike

easy to mount and holds my rifle sturdy.