Your cart is empty.
Your cart is empty. Specifications:
Rated Voltage: DC 24V
Reduction Ratio: 1:22
No-Load Speed: 200RPM
No-Load Current: 0.1Amp
Rated Torque: 1Kg.cm
Rated Current: 0.3Amp
D Shaped Output Shaft Size: 6*14mm (0.24" x 0.55") (D*L)
Gearbox Size: 37 x 24.5mm (1.46" x 0.96") (D*L)
Motor Size: 36.2 x 33.3mm (1.43" x 1.31") (D*L)
Mounting Hole Size: M3 (not included)
Application:
Vending equipments, pan camera, slot machine, money detector, coin refund devices, automatic doors, peritoneal machine, toys motor etc.
Packages:
- 1 x DC Geared Motor
PLEASE NOTE:
1.Use tolerance: Pay attention to the use of voltage and current range, otherwise the motor performance and motor life will decline.
2.Handling motors: Gently, as far as possible the use of motor shell part.
3.Motor wiring: Red lead to the positive electrode, black lead to the negative pole, if reversed, the motor rotation in the opposite direction.
4.Overload: As far as possible within the specified load range, prohibit motor blocking or close to the stall state for too long time to runs. Otherwise, the motor will burn out.
5.Motor storage:
-- Storage temperature: 0℃ - 40℃;
-- Storage humidity: 15% -90% RH;
-- Avoid placing in high temperature, high humidity and corrosive gases.
6.Motor use temperature: 0℃ - 70℃
J. Parral
2025-08-30 18:03:57
The size of the motor was perfect to create a rotation device for a roaster. Low noise, just the right amount of power as I wanted to spin slow. It worked as intended.
Mukesh Jadhav
2025-08-15 10:12:43
Works just fine. I needed a DC motor for my DIY project and I see no issue's with this motor. up to 15 kg torque.
SB rc
2025-07-13 16:15:39
Very good quality no issues at all
Joshua Cole
2025-07-08 10:45:56
This motor works pretty well but it's definitely a little faster than 100RPM. I had to make my own rpm calculator to properly measure the exact speed because it was not matching up with expectations. That's fine. The more egregious problem I'm having is that the shaft wobbles a lot. Overall not a deal breaker, just be aware of this possible defect.
Matthew R
2025-06-23 10:56:41
I built a filament respooler that called for a 100RPM motor. (not pastamatic, the original one) I bought the recommended motor but it was loud and to be honest, a bit slow for my tastes. I found this motor which is faster and quite a bit quieter. (by no means quieter, just a lot quieter than the other motor I used) I am guessing the noise is from the gear box. I can use full speed on my motor controller but it is a bit too fast. I can slow it way down and it still works. At a certain point, slow is just off. (pretty close to the off position) I recommend this over the motor listed on printables because it is quieter, faster and much less expensive.
Songhai Chai
2025-06-11 16:50:23
it met my expectations for my experimentation
Customer
2025-06-10 13:28:11
This motor and gearbox work just fine, however you should be aware that the motor itself is quite loud. I’m replacing an old worn out motor/gearbox with the same specs, and this new one is twice as loud as the old one.
David Dumbrell
2025-04-18 18:56:12
needed a faster rpm and this motor was the answer. The attaching screw pattern was a perfect match to a motor I bought years ago, nice a quiet also.
Antonio Gutiérrez
2025-04-16 12:14:37
Era exactamente lo que necesitaba, quedó muy satisfecho.
Peter P.Schrick
2025-04-09 21:32:35
....schon mehrmals gekauft und entsprach ganz meinen Erwartungen.
Mr Nathan Webb
2025-02-15 14:49:17
I used it on my lifesize R2D2 to rotate the dome. Works perfectly, wired it up no problem.
GianPiero
2025-02-10 11:14:38
Tutto ok come da descrizione.
Recommended Products
