Shopping Cart

Your cart is empty.

Your cart is empty.

HC5345 Seal Kit Fit for Seastar Front Mount Hydraulic Steering Cylinder Seal Kit #HS5157 & Steering Support Bracket Puller

4.8 (8) Write Review
Free shipping on orders over $29.99

$46.99

$ 23 .99 $23.99

In Stock
  • 【Application】①Front Mount Hydraulic Steering Cylinder Seal Kit -- Fits front mount cylinder parts: HC5340, HC5341, HC5342, HC5343, HC5344, HC5345, HC5346, HC5347, HC5348, HC5358, HC5365, HC5375, HC5394, HC5445, HC6750, HC6751, HC6752, HC6753, HC6754, HC6755 (All Model Front-Mount Cylinders Except HC5340) ②Hydraulic Steering Support Bracket Puller -- Fits for SeaStar and Uflex support brackets.
  • 【Function】①Front Mount Hydraulic Steering Cylinder Seal Kit -- Used to repair leaking or weeping cylinder seals. Replacement hydraulic seal kit for pivot / front mount hydraulic steering cylinders on outboard motors. Kit fits most outboard boats with single or twin engines. ②Hydraulic Steering Support Bracket Puller -- Safe and quick removal support brackets.
  • 【Material】① Front Mount Hydraulic Steering Cylinder Seal Kit -- HS5157 kit is made From High Quality Aircraft Grade Aluminum. ②Hydraulic Steering Support Bracket Puller -- Made of high-hardness 4140 impact-resistant steel with a black oxide coating for rust resistance and durability.
  • 【Design】① Front Mount Hydraulic Steering Cylinder Seal Kit -- The entire steering system is always sealed during the deflation process to ensure that the fluid flows to where it should go. ② Hydraulic Steering Support Bracket Puller -- Teeth design can grip the bracket stably, Using a 3/4" drive to tighten the head long bolt to press the bracket out of the steering.
  • 【100% Satisfaction Guarantee】If you're not 100% satisfied with our tools, simply return it for a full-refund in 30 days. Support 12 months’ Warranty. Professional & Sincere Service allows you to take no risks to purchase in Yoursme!


Product Description

1

HS5157 Front Mount Steering Cylinder Seal Kit with Wrench

1

Choose Yoursme, choose excellent products！

Powerful Functions
  • Used to install the pivot/front hydraulic steering cylinders.
  • This seal kit fits for most outboard boats with single or twin engines.
  • Used to repair leaking or leaking cylinder seals.
High Quality

  • Made from quality billet aluminum, corrosion resistance, anti-rust, sturdy and durable.

Fitment

Seal Kit compatible for:

  • -HC5345, HC5340 and HC5342 (threaded end gland)
  • -HC5347 (Pivot Cylinder, Honda 115-130 specific),
  • -HC5348 (Pivot Cylinder, OMC 77-90 specific),
  • -HC5365 (Compact Cylinder (threaded end gland)),
  • -HC5394 (SeaRay Compact Cylinder (obsolete) (threaded gland)).
Warm Tips

  • Use the adjusting nut inboard of the starboard support bracket to remove steering slop.
  • Once the tension screw is loosened on this nut, turn it counterclockwise by hand to remove any slop, and then retighten the tension bolt.
1

  • 1. Loosening the Seal Gland. Turn the outboard hard to port; place the pin wrench in the holes of a gland. And use a 5⁄8-inch box wrench on the nut on the port end of the piston rod. (NOTE:Turn counterclockwise on the pin wrench with opposite pressure on the box wrench to loosen the seal gland)
  • 2.Removing the Support Bracket. Use a 3/4-inch socket wrench to remove the nut and washer securing the support bracket to the support rod. (Do the same to the piston rod nut and washer. ) Use wrenches on the opposite ends to keep the rods from turning. With hardware gone, pull off the support bracket.
  • 3. Use the pin wrench to remove the Old Seal Gland.
  • 4.Install the New Seal Gland. Place the tapered guide tool from the kit on the end of the piston rod and lubricate it and the piston rod well with oil or grease. Carefully slide the new seal gland over the guide and onto the piston rod until it reaches the cylinder. Screw the seal gland into the cylinder, but don't tighten it yet. Remove the guide tool; it is not part of the final assembly, but you will need it for the other side.
  • 5. Reinstall the Support Bracket. Reconnect the support bracket to the support rod and piston rod and replace the washers and nuts, tightening the nuts against the washers. You may need to use wrenches on the opposite nuts to tighten sufficiently.
  • 6. Tightening the New Seal Gland. Use the pin wrench to tighten the new seal gland while using a 5⁄8-inch box wrench on the starboard end of the piston rod for counter torque.

Hydraulic Steering Support Bracket Puller

1

Application & Design

  • Fits for SeaStar and for Uflex support brackets.
  • Teeth design can grip the bracket stably.

1

Function

  • Used to safely and quickly remove for SeaStar and for Uflex support brackets.
  • Using a 3/4" drive to tighten the head long bolt to press the bracket out of the steering.

1

Material

  • Made of high-hardness 4140 impact-resistant steel with a black oxide coating for rust resistance and durability.

Instruction of Hydraulic Steering Support Bracket Puller

1

Step 1

Remove half of the bolts, then insert the puller into the bracket.

1

Step 2

Tighten the bolts to secure the bracket.

1

Step 3

Use the driver or sleeve to tighten the bolts and press the bracket outward.


Bassmantf196
2025-08-21 18:19:41
Worked perfectly and was very easy to install. Cost was half if not more less than boat shops.
RickyBobby
2025-07-27 12:39:28
My SeaStar seals were really tight and I was afraid to break or damage the wrench provided so I used a large channellock wrench to break it loose. The rest was really easy.
adrian saavedra
2025-06-11 13:24:03
Where do I start? I guess I should have known when the pin fell out of the pin spanner before using it to install the seals, then I Used the boat three times and the seals started leaking and was just able to return to the dock before I lost complete steering control. I don't normally leave reviews but these seals can ruin your day if you loss steering.
customer
2025-05-26 15:04:33
Easy to get install has been on boat for 2 weeks and 3 trips so far no leaks
R. Peleske
2025-05-01 16:14:27
Can not say how long it will last but appears it will last for anytime I need it in the future. It definitely made the job go a lot quicker than I expected. Not the first owner of this boat and did not know how hard it would be to accomplish changing the seals. Would recommend this product.
M. Lehmussaari
2025-03-01 11:10:37
Opening tool is too weak to open the sylinderhead. Fortunately I had Yamaha's own tool to use. Otherwisethe kit was good.
Customer
2025-02-28 15:01:56
The item came quick it was easy to install and i have not had any leaks since i did it and it’s been almost a year.
Harvey W.
2024-12-05 16:41:09
The seal tool is crappy. Broke on the first use. Spent $67 on the right tool and it came out instantly. The seals are OK, but the tools are just crap.