Your cart is empty.
Your cart is empty.A heavy duty actuator with a stroke length of 8". This uses a power supply of 12v-24 and will operate faster with a 24v supply. It will extend or retract 0.315 in/s (8mm/s) at 12v and 0.670 in/s (17mm/s) at 24v. The maximum load (push or pull) is 330 lbs (1500N). This unit has built-in limits switches to cut power automatically at the end of travel. This can be used in harsh environments as it is IP54 rated (weather resistant). This actuator has a position feedback mechanism based on pulses from a hall effect switch. When read by a microcontroller, each pulse represents 0.007046 inches (0.17896mm) or travel. Use of this sensor is completely optional and can be left disconnected. The mounting brackets and pin are included. The wire leads are 3 feet long (1 meter) and have exposed, tinned ends. When positive supply voltage is connect to the Red and Black leads, the actuator will extend. To use the hall position sensor, connect Green to ground, White to supply (5v), and Yellow to a 10k pull-up resistor. The pulse output can be read from the yellow lead
Brian Robertson
2025-08-19 13:56:31
I bought this to use in a industrial setting. We've been doing lab testing with this actuator now for a two months and it's performed amazingly. I know that's not a super long time, but we've put it through some hard living. It's been in/out as much as 100 times a day, dropped(more than a few times), accidentally blocked from moving, covered in grease and oil, and various other mistreatments. It still works flawlessly.The only complaint I have is the packaging. It arrived in a plastic bag with not a shred of padding. I don't know if that's on Amazon or the manufacturer, but it was pretty badly beat up when I received it. I would have likely returned it if I wasn't in an urgent need for it and if I wasn't about to ding it up myself.
Mike
2025-07-30 12:53:23
Using twp of these to position some mirrors to reflect the sun to a solar collector. Tried to very the speed of the actuator, using pulse with modulation (PWM), that worked OK, but the position feed back, from the actuator, drifted when ever I drove the motor with PWM. If I drove the motor with a steady voltage, the position pulses did better, but still would drift depending on how often the motor would change directions. I used these outside, and yes I know they were not rated for wet areas. After about a year, some internals of one of the motors got corroded, and I took it apart, to see how it was constructed. It was constructed very well and also found, out how the drive limits worked
Customer
2025-05-13 15:51:57
This is the third one I bought. When it arrived Amazon forgot to pack the mounting brackets and pins. Zoom Industrial was notified and the brackets and pins were promptly shipped and delivered in 2 1/2 days. Very pleased with the product and service.
Iraiza Porter
2025-04-27 18:15:45
I installed it to open and close the louvers over my indoor pool. After only a few uses, the plunger came apart. Maybe it is only designed to push and not to pull, I don't know, but it did not do the job at all.
dan oconnell
2025-04-16 17:45:54
Love it! I used it for my Motorhome traveling step.
KT
2025-04-15 10:35:44
This is a very nice actuator, either 12 or 24dc I hooked mine up to a 24vdc supply. I am using it to lift a mattress with under-bed storage in my travel trailor. Surprise at how quick it lifts. Would have given it 5 stars but one clevis pin and two cotter pins were missing, which left me scrambling to find substitutions. Sorry but no excuse for missing parts just lack of care.
Campbell
2025-03-28 15:55:44
Didn’t come with the mounting hardware that was promised. Now I have to waste my time sending this item back just for the mounts. *Update* I reached out to the manufacturer directly and they got me mounting hardware in the mail same day.
Danny
2025-01-18 13:17:14
Great product. Has held up very well considering it's been outside since the day I got it.
Recommended Products
$80.95
$ 31 .99 $31.99