Your cart is empty.
Your cart is empty.Product Description
Efficient
Eliminates mistakes of measuring each door and drawer separately.
Precise
Adjustable Hardened Steel Drill Guides for perfectly straight holes.
Long-Lasting
Impact resistant construction makes it strong and durable.
Customer
2025-08-30 15:12:55
Absolutely saved my sanity with all the holes I had to drill. I wish it could do larger sizes, but it got most of the job done and I could still use its center hole for the extra wide tasks. You must buy a clamp separate though, or else this product will not work well.
Reviewer
2025-08-18 13:23:16
Easy to use. Nice and straight. I wish I'd gotten this sooner.
Columbia_MD
2025-08-12 13:11:30
HIGHLY RECOMMEND.Outstanding product. I purchased it after watching a clip on You Tube about using the product. It is accurate and must have. I used it to install 61 cabinet/drawer pulls. In addition to this item, a must have item is the “Kreg KHC-PREMIUM Face Clampâ€. When using this clamp, DO NOT clamp on the back guide (it will mess up the measurement). I wish the clamp was 1â€-2†longer to give more clearance/flexibility while drilling. Another item to purchase, if you do not have one, a $2.00 “clear plastic ruler†to measure distances between the jig and the edges of the cabinet. Use 0.5mm pencil and not a regular/carpenter pencil when making marks. Use alcohol swabs then wipe with a damp cloth/paper towel to remove pencil marks.For the 2 large kitchen drawers, where the jig does not extend, I removed the jig’s guide and positioned the jig where I wanted it. The clamp did not reach. I drilled the 1st hole then inserted a second 3/16†bit in the drilled hole. I re-aligned the jig, held it in place with my hand while drilling the 2nd hole.I installed 61 pulls – 122 holes and all are perfect. This jig enabled me to make straight holes which is a must for installing pulls. Cheaper templates simply tell you where to drill and do not assist in the drilling process. Spending $40.00 on the jig and clamp is the best thing I have done to avoid costly mistakes.HIGHLY RECOMMEND.
R. W. Ashmore
2025-08-07 18:14:31
I had a very difficult time seeing the numbers on the jig while lining up the numbers to the markers on my cabinets. Taking some white acrylic primer, I glazed over the numbers on the jig. After doing so, the results were fantastic! The jig is otherwise accurate and very easy to work with as well as durable.
Zacky
2025-07-22 16:52:47
This is the first jig I have used on cabinets. It was simple to figure out and because of the solid design gave me confidence I was drilling accurate holes which was very important to me.
Recorder
2025-07-06 13:46:33
This is one of the best purchases I have ever made. This jig is perfect for drilling accurate holes for knobs and pulls. The adjustable spacing with click stops at common spacing, the calibrated fence and the sight window makes it fast and easy to get perfectly aligned cabinet hardware every time. The hardened steel drill bit guides keeps the holes perpendicular to the drawer or door. Perfect for both 1 hole and 2 hole hardware. Do not wast your rime with one of those cheap plastic templates. This is well worth the extra money. Once you set up the first piece of hardware, the rest are really quick and easy to duplicate. The Kreg face clamp works very well keeping the jig in place while you drill and I would recommend getting it also.
ERL
2025-06-06 11:34:55
Works as you'd expect. Easy to set up and adjust. Wish it came with the clamp but just used one I had.Had all new cabinets to install hardware on and this saved me a lot of time. We had a custom island built and installed. The company that built it, installed it and put on the hardware (pulls). I offered the jig for them to use but they decided to do it the way they are used to doing it. The only crooked pulls in the kitchen are on the island.We also have a spice drawer that didn't fit our 5 inch pulls due to the way it was constructed. Had to get a 3 inch one for this one drawer. The jig is so easy to adjust. 5 mins later I had the 3 inch pull installed.
P. de Greyt
2025-05-27 16:57:54
I used it to refresh my kitchen cabinets, it was a total time saver, this wasn't my first rodeo but I had such a bad experience I told my wife that I was going to get a jig so I didn't wind up with Swiss cheese for cabinets. I have used Kreg products in the past and have been always been very happy, so I decided to get this jig to help with the refresh, boy did it ever deliver, it was easy to assemble and easy to use, it made my refresh a breeze. I strongly recommend this jig to anyone who has a need for putting pulls and knobs on. Not f you are a pro this is a time saver, if you are a hobbyist this will save you a lot of headaches.
Mzee
2025-05-15 11:07:44
Okay, it looks plastic. I was a bit skeptical. But in three hours I put in all the knobs and handles in my new kitchen and they are all perfect. After the installs, I inspected the metal insert bushings that guide the drill bit: no wear. All holes are drilled true too. The presets make handle alignment easy and the centering guide makes finding your centre line a snap. I wish there was a way to auto centre rather than measuring but it still works great. I gave it a four on ease of use because you have to measure accurately to get your centre line. That is not a problem with the tool per se but a warning to users to be careful. take your time and get it right. DO a couple tests on scrap. Definitely use it with their flat faced locking pliers.
KeithEvans
2025-04-20 12:26:11
Excellent piece of kit does what it says on the boxIf you're fitting a kitchen you definitely want one of these for the door handles
MAURICIO ALDANA
2025-03-05 10:11:34
MUY BUEN PRODUCTO, CUMPLE CON LO QUE PROMETE, MUY BUENA CALIDAD
Jbmauser
2025-01-14 18:00:47
Did 20 drawers with this and a couple cabinet doors so far. Super time saver and accurate! Well worth the money!
Pascal Dolan
2025-01-07 15:59:21
As described and on time
Recommended Products