Your cart is empty.
Your cart is empty.Product Description
Features
Various Size
There are various choices for your DIY project. Each size come with multiple quantities.
Internal view
Precise opening, suitable for small electrical projects.
For internal size confirmation
In order to confirm the detailed installation dimensions, please refer to our detail image, which shows specific internal dimensions of the product.
Brian
2025-08-15 12:12:13
Used as junction boxes for LED light bars in my barn. I didn't want a big 4" box at 8-10$ a piece. lower profile and lower cost. Worked perfect for what I wanted. Just had to drill the holes.
Ashley Regan
2025-08-07 18:15:33
Good Product
rootDG
2025-08-06 15:34:00
Well made and great quality. It didn't work for me because the height was just a 3mm too small.
Christopher
2025-06-20 13:24:49
Pretty good little project boxes that snap together well. There is a hole on each end for wires or maybe even an LED to poke out. I also have used a couple to hold Raspberry Pi Picos with pins when storing them so the pins don't get bent, etc. The ones that are a little bigger would make a good Pico case where you want to have a USB wire come out, you have to allow some length for the plug itself to fit inside of the case with the Pico
Bob Loeffler
2025-06-13 17:42:43
These boxes are good for small electronics
Doc D
2025-06-10 18:19:55
It's just a box. Clever snap-on lid. Dimensions are given for everything except the one dimension that's hard to measure - that is the dimensions for mounting a board. So you have to try and hover your caliper over the mounting holes. As someone else has mentioned, there are no screws for mounting the board or even any part number for the screws. In short, the manufacturer could have made our job easy but chose to be lazy and make all of us figure it out. FYI, my best guess is 87mm x 48mm spacing for the PCB mounting screws, but my eyesight isn't what it used to be. I found some screws that seem to work so I don't have a part number. And finally, the mounting posts are too close to the corners leaving too little board material between the mounting hole and the inside wall. And watch out for the inside dimension because the wall slopes and gets smaller as the board is lowered down. So, if you use their dimensions, the board will be too big and require lots of hand filing. If you make the board shorter to fit the real size, the PCB will not have enough material between the mounting hole and wall. (This review is only for the case measuring 3.94 inches outside)
S.S.
2025-05-14 20:14:00
But they work great! My suspended desk slider needed raising juuuuuust a little bit. But not raise up so much my keyboard and mouse get squished. They look nice too, like it's part of the slider. These were a very inexpensive solution to an ergonomic problem. I used four of the five and maybe I can use the fifth as an actual container. Ha!
Douglas A Hottman
2025-05-02 10:26:09
I have used these boxes for two projects that use a ESP32-DevKitC-32E Development Board. In one case I have an Ultrasonic Module HC-SR04 Distance Sensor mounted in the box along with the ESP32 board. As can been seen I have cut holes through the box for the ultrasonic transmitter and receivers. The other use is only mounting the ESP32 board inside the box and running wires to a temperature and light sensor through small holes. In both cases I cut a slot for the USB connector to connect directly to the ESP332 board. The lid snaps on tightly, but is not overly difficult to remove.
Mallcoms
2025-04-27 11:31:28
Nice convenient size. Great value.
customer
2025-03-16 16:12:21
Installed timers for lights in my truck nice compact size
Cam
2025-03-08 11:08:27
Pretty good quality
Manche de pelle
2025-03-01 15:02:39
Good product to all my DIY products. Bought it at a discounted price and cheaper than elsewhere
SK S Dartmouth, NS
2025-01-31 11:47:54
These utility boxes were perfect as junction boxes on interior wall for usb cables feeding outside security cameras.
Recommended Products