Your cart is empty.
Your cart is empty. Helps Stop Damage to Pulley and Shaft.
Designed to ease the operation of pulling the balancer pulley. It reduces damage to both the pulley and the shaft.
JOHN in CA
2025-08-31 18:13:52
Worked perfectly. I just used this to very easily remove the Harmonic Balancer on my 5.8L Ford engine in my '95 Bronco. The two bolts provided for the specific threads in my ford balancer, easily screwed into the balancer and did not suffer any distortion or breaks that some have had issues with when pulling the balancer off. The center screw with the rotating cone on the end left the crankshaft screw hole in perfect condition. Make sure you have the tool balancer screw heads going against the flat side of the puller casting or you will distort and/or break these bolts if pulling against the angled casting side. The instructions don't make that clear, and while it should be obvious, pulling against the wrong side of the casting may be what caused some to have problems.
Travis M.
2025-08-25 18:50:27
Lisle has always been a great product. I only wish it came in a blow mold case. I highly recommend this product.
Nicolaas Van De Houten
2025-08-08 11:12:25
I've used it about 6 times now. It has worked great, but I wasn't thinking this last time and I think I used it improperly. Ended up bending one of the provided bolts. There is a size that works for Toyota/Lexus vehicle Harmonic Balancer (crank pulley) provided, and that is the one I'll have to find new bolts for in order to continue using it. The cone cap on the main threaded center bolt also seems to not lock securely the same way it did at first - after this last use. I think it'll continue to work though. That last car's pulley was more stuck than most I've recently encountered.
mike g.
2025-07-26 13:57:44
Worked great and its a bargain for the quality. I believe this is the lowest price for this on amazon. Can also be used to lift a Yamaha 300hp - 350hp outboard if you weld a ring to the middle puller part.
Liane
2025-07-03 17:14:14
The puller casting is thick and strong, which is what you need for tough jobs on older vehicles and tough climates
Thumper
2025-07-01 14:19:16
I ended up buying a 3 prong puller. Worked great!
Glenn
2025-06-20 17:07:09
This puller was used to remove the damper pulley on a Ford Taurus. The factory tool was 180.00 best price. This did the trick for a sixth of the price. It brought the cost within reason and worked very well. I'm happpy!
Ryan
2025-06-14 11:54:57
Worked well on a 7.3 power stroke balancer. The set seems to be sturdy though I have only used it once so far. It would have been nice if it came with a storage case.
zozapan
2025-06-11 19:57:50
This is a tougher unit than the typical cheaper ones. Get yourself some extra thick washers to use with smaller bolt’s.
katrina banks
2025-03-16 17:24:18
Terrible quality, badly packaged with zero protection so all the puller and all the hardware smashed into one and other. Everything damage, but also, just terrible manufacture, NOT what they use to be. it’s junk - don’t recommend.
Grandin St.Germain
2025-02-21 10:37:07
Works well. I have used it 5 times so far to remove the flywheel off of outboard motors. The bolts supplied do not fit the flywheels so they had to be purchased elsewhere. Good value.
Marcel
2025-02-19 14:37:50
works good
WAI
2025-02-07 15:59:50
ok
Recommended Products
$11.99
$ 5 .99 $5.99