Your cart is empty.
Your cart is empty. The M18 Fuel 5-3/8" – 5-7/8” metal saw delivers the fastest cuts with the longest tool life and up to 370 cuts in ¾” EMT.
this compact and lightweight metal cutting Saw utilizes a power state Brushless motor with 3, 900 RPM to deliver the fastest cutting speeds and longest tool life on the market. The metal saw also features Redline plus intelligence, The most advanced system of cordless power tool electronics, for maximum performance and unmatched durability.
Shane
2025-09-02 10:14:58
Very handy for cutting all kinds of metal or plastics, I use it quite often on fabricating and modifications.
BUYER BEWARE
2025-07-20 10:27:22
Awesome metal cutting saw.. not much it won’t cut through. Blades are expensive. Noise is excessive.
dusty
2025-06-19 17:24:03
Another remarkable tool from Milwaukee! I was looking for a efficient way to cut raised floor tiles at a data center I'm working at. It has done wonderful. Definitely saves time over a jigsaw or Sawzall with a non bur finish, and it didn't chip up the finish on top of the tile.
steve
2025-06-07 21:41:54
I've used a 4-1/2" metal blade on a mini corded wormdrive saw for years and always lusted for this saw. I saw that it was heavily discounted so I finally bought it and it has exceeded my expectations after cutting a heavy duty metal door (3/32" sheet on both sides with nearly 2" of foam in the middle) into smaller chunks like it was cutting through 1/8" lauan board. Having the clear chip gaurd on the front is just icing on the cake - I no longer need to wear a blast suit when using a metal saw as it keeps all the shavings well under control! The stock blade is great but it's a standard size for metal blades so this saw will hopefully live a long hard life in my shop! If you have any projects with metal sheets in the future - this is a tool you really should consider purchasing!
Tony
2025-05-28 14:50:20
Works great..
Francis Basham
2025-04-30 12:42:03
Bought this for my son He is in commercial electricity cutting pipe to run cables. Says cut like butter and better than any band pipe cutter loves it .cuts 3 inch metal pipe without hesitation
bruce
2025-04-25 15:01:22
Tool came fast, well packaged, and ready to go. I like I could buy tool only as I have plenty of batteries. The first cut I made with this saw was 2"x4"x1/4" walled steel. Had I more experience with the saw it would have done the job in one pass. With the included blade 2 inch cut, you really have to keep the saw flat and tight to the surface of your material. I plan to get the 5 7/8 " blade this week to help with that. My guess is when you take your new saw out of the box you will be thinking you bought the wrong saw! I did. Watch some YouTube videos on this saw, and I assure you this saw will do what you see it do the way it does it in the video. My favorite introduction to this saw to my friends is to cut a scrap piece of 1/4" flat stock and put the cut directly on my face. It really is not hot at all and a mirror cut. You will not regret this saw. Just like every other Milwaukee tool I have, I wonder, where has this been my whole life? Really great saw, light weight, feels good in your hand, makes straight cuts easily. JUST ORDER IT !!
Dave
2025-04-08 16:45:12
I bought this saw specifically for its light weight and small size. I already had a (corded) Fein Slugger 9" worm drive metal saw, and I had been looking forward to the release of the Milwaukee Fuel 8" Metal Saw, but decided what I was lacking more was something with easier handling for, say, going up a ladder and cutting a fairly small piece. A large saw can be really clumsy and precarious doing that sort of thing.Besides cutting metal tubing, sheet, and plate, I have used it to cut plywood, 2x4s, and PVC pipe. The blade isn't particularly fast for cutting wood, but it works pretty well. For PVC, you can get a real clean cut--much better than using a hacksaw or sawzall, IMO.This is an awesome little saw, but I found a couple of its limitations. First, cutting longitudinally through a weld bead on 1/4" mild steel plate (about 3/8" total thickness), the residual stresses in the metal began to pinch the blade pretty good. The little saw was powering through it, until after about 3-1/2" out of maybe 6 or 7", the heat protection would apparently shut it down. It was then a pain to extricate from the cut, and several carbide tips were damaged and lost in the process. I actually repeated this twice before I realized the saw had shut itself down. Also in the process, the abundance of hot chips partially melted through the lower guard (some blistering on the outside). After this, I got out my Fein Slugger 9" corded saw, and powered right through it all.If it had not been for the pinch due to the weld bead, I think the only problem would have been the guard melting--which would have actually been worse.One thing a buyer should be aware of is that there is no bevel adjustment for this saw--90 degree shoe angle only.
Omar León
2025-04-06 16:16:18
Corta el metal como mantequilla, considera tener aire comprimido a la mano para su limpieza y no dejar que se atasque de rebabas la guarda
Raymundo E.
2025-02-17 12:36:48
La marca lo dice todo,, sinonimo de calidad..solo un comentario con la empresa de paqueteria que segun la direccion de entrega estaba erronea, pero no fue asi verifique y estaba completamente correcta. aqui la cuestion es que fue un pretexto para poder sacar dinero argumentando que estaba ya fuera de ruta...Amazon suguiero que pongas mas atencion en esos detalles..
Xavier
2025-02-01 11:37:58
Llego en su empaque original. Incluye su disco y llave allen.Corta los tubos como mantequilla... excelente producto.Los cortes son como hasta 2 pulgadas de profundidad aprox.
Cliente de
2025-01-01 16:00:10
Con la calidad que respalda la marca. Es ligera, y versátil. La potencia también depende de la baterÃa que le instales.
Melvin Medina Rivas
2024-11-24 11:44:30
Excelente herramienta, buen rendimiento de bateria
Recommended Products
$399.00
$ 99 .00 $99.00
$154.99
$ 76 .99 $76.99
$235.00
$ 99 .00 $99.00