Product Description

For Honda:

2003-2007 Accord L4 2.4L Accessory Drive Belt-Accessory Drive

Measure Serpentine Belt Length Method 1: Using an Existing Belt

Mark a line across the belt with a white marker

Line up a measuring tape with the line on the belt

Wrap the measuring tape around the belt until it meets the mark

Hold your finger where the tape meets the mark and note the distance

Measure Serpentine Belt Length Method 2: Finding the Size Using the Pulleys

Use string if the belt is on the pulley or if there is no belt

Hold 1 end of the string on top of the belt or 1 of the pulleys

Wrap the string around the pulleys until it meets the other end

Mark the string where it meets the other end and remove it. Then lay the string flat and measure the distance between the end and the mark

How to Replace a Serpentine Belt

Pull the hood release inside the cabin of the vehicle. To access the serpentine belt, you will need to open the hood of the vehicle

Disconnect the battery. You should always disconnect your battery before starting an automotive project

Locate the serpentine belt. Depending on the engine in your vehicle, the serpentine belt may be located at the front of the engine bay, or it may be along one side. There may be engine covers in the way, so be prepared to remove them if need be

Find the serpentine belt routing diagram. Many cars come with a sticker in the engine bay that shows exactly how the serpentine belt is supposed to be routed through the various pulleys on the engine. If your vehicle does not have a sticker, you will need to find another way to remember how the belt should be run:

Look in the owner's or service manual for your specific year, make and model vehicle for a diagram

You can also take a picture of the existing belt with your cell phone to use as a guide when installing the new one

Use a wrench to relieve the auto tensioner, loosen the bolts in the alternator bracket. As you loosen the bolts, the tension on the belt will likely move the alternator toward the engine and relieve the pressure

Then pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine

If the belt is severely damaged, be sure to remove any parts that may have come off of it as well

Compare the new belt to the old one and make sure it is right one. Look at the new belt in comparison to the old one to be sure they are the same width and have the same number of ribs going across the belt horizontally

Route the belt through the pulleys. Run the new belt through the pulleys in exactly the same way the old one was. Refer to the belt diagram in your vehicle's owner's manual or the picture you took of the belt before removing it to guide you

Then apply pressure on the auto tensioner and put the belt over it.

KOFI

August 28, 2025

I was very pleased with this product and quality

justin

July 14, 2025

It was the right part and arrived quickly

Gonzo

July 10, 2025

Works good.

Silvestre

July 5, 2025

Se mira que es de buena calidad

Ildifonso Chavez

May 25, 2025

Great price. For for belt and good material

Shane

April 5, 2025

Easy to put in, no squeezing or noises works like a charmðŸ‘Œ

sergio martinez

March 12, 2025

Did not fit, too short.I returned it

Dino

January 28, 2025

The belt seems to be of quality comparable to any other aftermarket belt. It was simple to install and had a very snug fit to it (I had someone help pull the tensioner so I could use both hands to get the belt set into place).

Shopping Cart

Your cart is empty.

MOCA 7PK1781 EPDM Serpentine Belt Fits 03-07 for Honda Accord 2.4L l4

1.Size:7pk1550

2.Number of Items:1

About this item

Product Description

Measure Serpentine Belt Length Method 1: Using an Existing Belt

Measure Serpentine Belt Length Method 2: Finding the Size Using the Pulleys

How to Replace a Serpentine Belt