Your cart is empty.
Your cart is empty.Mark Urso
2025-09-02 11:56:29
I'm no expert, but this is what I needed. Decent quality good price.
Kate
2025-08-09 12:19:01
Good quality, I verified accuracy. (No, I didn’t really). They are wonderful for purpose (which is helping me draw straight lines).
Jacob Birkett
2025-07-08 19:30:55
Note that the largest ruler does come with a sleeve just like the others; I just lost it.These four rulers are nice, made from stainless steel. The edges are sharp enough to slice you, which is good for accurately tracing lines. They come in two lengths and two widths.All measurements are in millimeters:The first is 355.50 long, 26.25±0.05 wide, 0.91±0.02 thick.The second is 304.50 long, 26.20±0.05 wide, 0.91±0.01 thick.The third is 203.00 long, 19.37±0.01 wide, 0.90±0.01 thick.The fourth is 152.00 long, 19.16±0.01 wide 0.90±0.01 thick.All measurements are approximate. All of them appear to be almost perfectly flat (which is impressive), and straight on the business edge.The markings are thin enough that you don't lose accuracy, and it is easy to precisely measure up to 500 microns. Even further, I found it easy to eyeball accurately down to 100 microns because the lines are so thin, straight and sharp. I also like the font.One issue you may note is that the ends are a cut a little bit rough. They have a slight bevel where a guillotine severed the length. Additionally, they do not appear to be perfectly perpendicular with the longest edges, and have a slight variance. This variance means that if you're trying to measure from the zero-end, your measurements will be off slightly. I have a picture attached with the markings lined up which illustrates this issue. It is more noticeable from the imperial side on the 300mm long ruler, which means that particular ruler has a slight offset on that specific side.As for the orange and transparent sleeves that they come with, I have a complaint. These are almost not worth keeping, but only almost. You can't hang them by a nail through the hole because the cut is on the wrong end (gravity), and this makes me wonder why the hole is there in the first place. The tops are also heat-sealed, which means that you can't remedy the problem by sealing the bottom and opening the top. I understand that these sleeves are almost definitively just for protecting the markings and brush texture during transit, and they are still useful for this purpose. Nevertheless, the material is thin and the design cuts prevent them from being more useful. It would have also been nice if cardboard outer-sleeve were more durable, as I would like to keep them in this. There is no easy way to open the package without ripping this packaging.All in all, great rulers for the price. Regardless of my complaints, this is still a 5/5 star item.
Collins D.
2025-06-27 14:58:53
THE VERDICT: Well worth the money, and I am a satisfied customer. If you are reading reviews because you are unsure, I recommend adding these to your cart.The Good: These guys are perfect for my primary purpose; scoring. They're thick enough to put some pressure against for a clean score as well as nice and straight for an accurate score. The lines are clear and distinguishable from one another making measuring simple if you can't reach it with calipers.The Bad: I took a star off because these do not necessarily start at a true zero. I've included pictures of the 6" and 8" as examples. The six is 4 thou off which is within tolerance for most light-medium duty applications. The eight is a good bit off zero and I might end up grinding it true one of these days. Finally, the holes in the sleeves are located such that if used for hanging, the rules will fall out. This is not a big deal to me though.
Art Lowell
2025-05-15 11:16:07
These rulers are heavy duty and more than meet my requirements for machine shop work. I especially like the 8 inch long one - very handy and not readily available elsewhere! Another feature I like is the fact that the 6" and 8" are 3/4" wide, the other two are a full 1" wide.One suggestion: Would like to see the company make another set that included USA 10ths and 100ths on the reverse side of the 32nds and 64ths side. This would be in lieu of the metrics side. Not complaining - There's nothing wrong with USA and Metric measurements on the same rulers! Just would be nice to have the option to order a set with USA on both sides, providing two alternate types of USA measurements.BTW: After all these years, I have to wonder why the USA is still plodding along with this old Imperial system!
Maleko
2025-04-16 11:56:09
Great price on three rulers. Metal rulers are the best and i use these to measure string height or pickup height on my guitars. The metal with black etched lines make it easier to read so i like them. I also tend to misplace these so having three helps a lot.
thomas
2025-03-26 11:01:01
These are the perfect ruler for every day use. Made with hardened stainless steel,they are both flexible and durable. They are easy to read an stay put!
Douglas R. Calverley
2025-03-20 17:09:12
This set of rulers are well made, sturdy and easy to read. They are thick enough to make measurements, make cuts and draw lines. Not as thick as "L" squares but they do not need to be, so they work good for me.
Alex P.
2025-03-17 18:40:40
Perfect set of rulers. They have every measurement i could possibly need.
Luis Carlos Davila
2025-03-07 14:09:44
Si se ven bien. El acabado de los bordes un poco filoso. No tanto como para cortarse los dedos (creo).
CD
2025-03-04 14:23:44
Sturdy, not flexible.
Charles Allen
2025-02-23 12:53:15
I’m embarrassed to admit that I’ve needed a proper mechanical ruler since the longest time . . .LOL.Well, I finally got fed up with my tardiness and ordered these. I’m totally pleased. These rulers are nicely etched and display nice, dark markings. Good quality stainless steel and easy to read markings - perfect for making accurate guitar pickup height and string height adjustments.
ING. SAMUEL CALDERON
2024-12-19 16:35:58
Excelentes reglas, recibidas conforme a lo mostrado en las fotogracias.
Recommended Products
