Your cart is empty.
Your cart is empty.Pcow
September 5, 2025
Very nice, high mass bridge. Solidly made and the brass saddle are great!
John Stephen
September 3, 2025
I used this as a drop-right-in replacement for the stock bridge that came with my Yamaha electric bass guitar. It fit right in, the screwholes matched exactly, and it is a very solid bridge that provides more clarity and resonance for the notes being played.
Evan M.
August 30, 2025
This is a very nice bridge for the money. It fits great on my daughter’s Kala Solid Body U-Bass. I had to drill new holes 1/8†further back, but it was worth it. This bridge has more mass than the Kala factory bridge and has brass saddles.
michael
August 28, 2025
Hard to find a replacement string- thru bridge for my Yamaha bb434 at any price. Either the string holes were in the wrong location or the didn't have the Fender 5 hole mounting pattern. What I did do was lengthen the string holes just a bit, and it works great.
KJ
August 4, 2025
Fit my Bronco Bass with no modifications. Looks awesome and sounds better because of the higher mass and brass saddles. My old bridge use to buzz at the saddles and this one doesn't so that's a great upgrade too.
M. Keefer
July 30, 2025
Believe it or not, I actually replaced a Hipshot Kickass bridge with this inexpensive Musiclily Pro bridge on an old beat up 80s made in Japan Precision Bass, and in all honesty I do not hear any difference in the tone or with the sustain. The reason I took the Hipshot off was because I installed tape wound strings and during setup I could not move the bridge saddle far enough back to properly intonate the strings. The intonation screws only go into the saddle so far before they bottom out, so I needed a more traditional bridge where the screws go through the saddle so I could move them farther back. I specifically bought this Musiclily Pro bridge not just to fix the intonation issue but also as an experiment to see how much of a difference a cheaper more basic bridge would make compared to a more expensive high mass bridge, and as I already mentioned it made very little to no difference, the bass still sounds and plays the same. I am very satisfied with the Musiclily Pro bridge and see no reason why it shouldn't stay on my bass.
Aiden James
July 29, 2025
Works as intended and dropped right in to my MIM Fender Precision bass and Squier Sonic Bronco bass. I use to love the Leo Quan Badass II bridge but it weighs 8oz. and the Musiclily bridge only weighs 5.7 ounces. I know it doesn’t sound like much but when you have a bad lower back every ounce counts. So I sold by Badass Bridge II and bought this.
Frank S.
July 5, 2025
I was pleasantly surprised. I’m a builder and can say quite honestly this is as good as the big named brands for less than a 1/3. Will be using them from now on
Franck
July 1, 2025
Très belle pièce en remplacement sur ma Jazz Basse. Le laiton sur le fond noir brillant est magnifique. Réglages comme sur la pièce d'origine et la peinture à l'air bien costaud ! Nickel, je suis très content de mon achat. Un délais de livraison un peu plus long que d'habitude avec Prime mais bon, le résultat est là !
Luigi Joseph Del Giacco
June 28, 2025
Il prodotto è perfetto per lo scopo: ben costruito e ben rifinito. L'ho preso per sostituire il ponte di un basso che ho da anni e che era difficile da regolare (ponti monorail stile Spector. Questo invece è semplicissimo: il classico ponte Fender style, ma con una massa maggiore e sellette in ottone. Nulla da eccepire.
James
June 15, 2025
Bought this as a replacement for my MIM 50's series PJ bass bridge, which was thin and rusty.Right away I was pleased with the heft. It's almost 100% increase in mass from the old bridge (79g - 155g)Installation was easy. Included screws fit right in the same holes.Looks nice.Adjustments are easy.For the price, you can't go wrong.
Martin O'Connor
June 7, 2025
Solid, well made construction. Minor modifications (new screw holes only) were required to fit on a Dean Metalman Z bass.A previous owner had already changed the bridge but had done a poor job of it - big gaps between the saddles. This bridge has corrected that and has dramatically improved the instruments playability and tuning stability. Strings feel more stable and feel "tighter".The bridge weighs approx 98g, similar to most standard bass bridges. Not high mass, if that's what you're looking for.Definitely an upgrade to the bridge that was on the bass and I'm very happy with the results.
Manel M.
May 27, 2025
Soy bajista veterano pero nunca me he lanzado a hacer mi propio bajo. Compré como base un Harley Benton JB-62 tipo Jazz Bass al que voy haciendo modificaciones. Buscaba un puente negro un poco más robusto y con guÃas para las selletas, pero que fuera ligero.El puente está bien acabado, sin defectos de fábrica y bien pintado. Pesa 158gr. Los agujeros coinciden totalmente con el Jazz Bass de Harley Benton. Los tornillos que trae son muy buenos, la pintura ni se inmuta al apretarlos.Hay que tener cuidado de no forzar los tornillos, porque entran un poco apretados (usa un poco de aceite de limón o agranda un poco el agujero, pero no fuerces).El ataque de las cuerdas se ajusta rápido con su llave allen. He quedado contento.
Pcow
May 25, 2025
Very nice, high mass bridge. Solidly made and the brass saddle are great!
John Stephen
May 18, 2025
I used this as a drop-right-in replacement for the stock bridge that came with my Yamaha electric bass guitar. It fit right in, the screwholes matched exactly, and it is a very solid bridge that provides more clarity and resonance for the notes being played.
Evan M.
May 18, 2025
This is a very nice bridge for the money. It fits great on my daughter’s Kala Solid Body U-Bass. I had to drill new holes 1/8†further back, but it was worth it. This bridge has more mass than the Kala factory bridge and has brass saddles.
michael
May 15, 2025
Hard to find a replacement string- thru bridge for my Yamaha bb434 at any price. Either the string holes were in the wrong location or the didn't have the Fender 5 hole mounting pattern. What I did do was lengthen the string holes just a bit, and it works great.
KJ
April 24, 2025
Fit my Bronco Bass with no modifications. Looks awesome and sounds better because of the higher mass and brass saddles. My old bridge use to buzz at the saddles and this one doesn't so that's a great upgrade too.
M. Keefer
April 17, 2025
Believe it or not, I actually replaced a Hipshot Kickass bridge with this inexpensive Musiclily Pro bridge on an old beat up 80s made in Japan Precision Bass, and in all honesty I do not hear any difference in the tone or with the sustain. The reason I took the Hipshot off was because I installed tape wound strings and during setup I could not move the bridge saddle far enough back to properly intonate the strings. The intonation screws only go into the saddle so far before they bottom out, so I needed a more traditional bridge where the screws go through the saddle so I could move them farther back. I specifically bought this Musiclily Pro bridge not just to fix the intonation issue but also as an experiment to see how much of a difference a cheaper more basic bridge would make compared to a more expensive high mass bridge, and as I already mentioned it made very little to no difference, the bass still sounds and plays the same. I am very satisfied with the Musiclily Pro bridge and see no reason why it shouldn't stay on my bass.
Aiden James
April 13, 2025
Works as intended and dropped right in to my MIM Fender Precision bass and Squier Sonic Bronco bass. I use to love the Leo Quan Badass II bridge but it weighs 8oz. and the Musiclily bridge only weighs 5.7 ounces. I know it doesn’t sound like much but when you have a bad lower back every ounce counts. So I sold by Badass Bridge II and bought this.
Frank S.
March 24, 2025
I was pleasantly surprised. I’m a builder and can say quite honestly this is as good as the big named brands for less than a 1/3. Will be using them from now on
Franck
March 23, 2025
Très belle pièce en remplacement sur ma Jazz Basse. Le laiton sur le fond noir brillant est magnifique. Réglages comme sur la pièce d'origine et la peinture à l'air bien costaud ! Nickel, je suis très content de mon achat. Un délais de livraison un peu plus long que d'habitude avec Prime mais bon, le résultat est là !
Luigi Joseph Del Giacco
March 16, 2025
Il prodotto è perfetto per lo scopo: ben costruito e ben rifinito. L'ho preso per sostituire il ponte di un basso che ho da anni e che era difficile da regolare (ponti monorail stile Spector. Questo invece è semplicissimo: il classico ponte Fender style, ma con una massa maggiore e sellette in ottone. Nulla da eccepire.
James
March 4, 2025
Bought this as a replacement for my MIM 50's series PJ bass bridge, which was thin and rusty.Right away I was pleased with the heft. It's almost 100% increase in mass from the old bridge (79g - 155g)Installation was easy. Included screws fit right in the same holes.Looks nice.Adjustments are easy.For the price, you can't go wrong.
Martin O'Connor
March 1, 2025
Solid, well made construction. Minor modifications (new screw holes only) were required to fit on a Dean Metalman Z bass.A previous owner had already changed the bridge but had done a poor job of it - big gaps between the saddles. This bridge has corrected that and has dramatically improved the instruments playability and tuning stability. Strings feel more stable and feel "tighter".The bridge weighs approx 98g, similar to most standard bass bridges. Not high mass, if that's what you're looking for.Definitely an upgrade to the bridge that was on the bass and I'm very happy with the results.
Manel M.
February 19, 2025
Soy bajista veterano pero nunca me he lanzado a hacer mi propio bajo. Compré como base un Harley Benton JB-62 tipo Jazz Bass al que voy haciendo modificaciones. Buscaba un puente negro un poco más robusto y con guÃas para las selletas, pero que fuera ligero.El puente está bien acabado, sin defectos de fábrica y bien pintado. Pesa 158gr. Los agujeros coinciden totalmente con el Jazz Bass de Harley Benton. Los tornillos que trae son muy buenos, la pintura ni se inmuta al apretarlos.Hay que tener cuidado de no forzar los tornillos, porque entran un poco apretados (usa un poco de aceite de limón o agranda un poco el agujero, pero no fuerces).El ataque de las cuerdas se ajusta rápido con su llave allen. He quedado contento.
Recommended Products
