Your cart is empty.
Your cart is empty.Product Description
Based on the popular and highly regarded KSA7575 universal mic attachment for keyboard stands, the KSA7575+ takes versatility A step farther. The "+" in KSA7575+ is its swappable mounting ends. Choose between the 5/8"-27 threaded insert or the u-mount style quick release stem. Both are included, so you can mount whatever you need! Use the threaded insert to mount mic clips, boom arms, goosenecks, or anything else with standard threading. Or use the stem instead and mount your u-mount series quick release tablet case...Integrating an iPad into your keyboard rig has never been easier! Like the KSA7575, the KSA7575+ locks securely into any keyboard stand with 1" Or 30mm tubing, round or square.
From the Manufacturer
Based on the popular and highly regarded KSA7575 Universal Mic Attachment for Keyboard stands, the KSA7575+ takes versatility a step farther. The "+" in KSA7575+ is its swappable mounting ends. Choose between the 5/8"-27 threaded insert or the u-mount style quick release stem. Both are included, so you can mount whatever you need! Use the threaded insert to mount mic clips, boom arms, goosenecks, or anything else with standard threading. Or use the stem instead and mount your u-mount series quick release tablet case...integrating an iPad into your keyboard rig has never been easier! Like the KSA7575, the KSA7575+ Locks securely into any keyboard stand with 1" or 30mm tubing, round or square.
MW
2025-08-28 15:31:43
Works well and happy with it! I bought this because I wanted to find a way to mount an iPad to my keyboard stand. It's small, fairly light, and fits into my keyboard bag, along with the Amazon Basics tablet mount which I can screw onto the end – a much more portable setup than the CTA gooseneck mount/clamp combo I used before. This attachment bar fits snug into the piping of my old On-Stage x-stand that I don't even have to tighten it much. The bar looks tall so I was concerned my iPad would sit too high above the keyboard but I'd say it's on the lower side, which is my preference. You can always buy other adapters or boom extenders if you want to make modifications, but this is really as simple as it gets, not to mention cheap.The thing about x-stands is depending on how tall you set it, the top supports can be either wide or narrow, so your music could potentially be far to your side. While the bar attachment does seem tight and sturdy enough to tilt to the side, I'd probably keep it pointing up at a right angle so as not to risk the weight of the iPad suddenly pulling it down. It really won't bring your music much closer to the center anyway, and would only bring your iPad down lower.
R. Shaw
2025-08-27 11:58:59
I bought this attachment to mount a microphone boom to the rear of this . I was worried it might not fit since the tubing on the Z-stand is square. Also, an earlier reviewer had specifically stated that it didn't fit this particular stand.Well I am happy (and relieved) to report to you that it DOES fit the "On Stage 2 Tier Folding Z Keyboard Stand". In fact it fits it perfectly; snug and secure. You can buy with confidence.I did also purchase the at the same time. It just makes sense to be able to remove the boom arm with a quick touch of a button, rather than having to mess around with rotating the entire thing to unscrew it. The quick release clip also gives the attachment a little extra height, and that's a good thing for anyone who might have a keyboard with a bit more height to it than normal.I'm extremely pleased with my purchase, and would definitely buy this same product again.That's it! I hope you find this review helpful. Happy shopping!
Mike Tarrani
2025-08-10 15:38:16
I have mine attached to one of the support arms on my . While this attachment is designed for both square and round tube supports, I was unable to use it with an even with the top tier removed. The reasons for the problem with the latter stand is the friction fitting on the attachment bar was too small for the oblong support tube, and had it mated, the height of the attachment bar would not have cleared the top of the keyboard.When attached to the with an attached to the top screw-in post that perfectly mates with the boom, this attachment bar/boom combination easily clears the height of either keyboard I use (a or a ).Bottom line, make sure your stand can accommodate this attachment bar (according to the manufacturer it will work with most X-style stands), and carefully measure the height of the top of your keyboard from the center of the support arm to which this attachment bar will be inserted. The total height of the attachment bar after insertion is approximately 7.5". If your keyboard is still too high for the attachment bar + boom or other mic holder to clear, you can gain an additional 3" with a .
David Schepp
2025-07-25 11:33:53
Mount works really well in my tube style keyboard frame and is very secure when in place. However, the threads that connect it to my boom stand strip/wear out very quickly. The metal/alloy used does not hold up to multiple uses. I have had to replace this mount and the mini boom stand(both from Onstage) multiple times because of stripped threads. This may not be a problem in permanent setups, but if you have to tear it down every night like me, this piece will wear out very quickly. I recommend purchasing a higher quality brand such as K & M if you are in this situation.
GSpring
2025-07-21 13:53:52
Works well
David J. Salto
2025-06-21 18:45:53
Awesome adapter!! Can't believe it works so great for such little $$. This works on my On-Stage and my Ultimate as well - as long as the tube inner diameter is around 1 inch or so it should work great. It fits well, locks in quickly and clears the top of my big Yamaha MOX8 nicely. It also doesn't sway or vibrate back and forth while I play. I can really hit the keyboard hard at times and this stays pretty solid. Maintains a nice low profile and looks nice too. I wish more people make add-on keyboard stand products like this. Before I found this, I was making my own adapters from old mic stands and they were ok. But I was so glad I found this. I have 2 - one for my mic and one will adapted to hold my Mac. This is a really great product and I highly recommend it!!
Barry W
2025-04-16 13:51:46
I bought this item along with the mic boom that screws to it. It holds my microphone securely, eliminating the need for a tripod type mic stand. Very pleased with it.
Lala
2025-04-01 20:35:44
Great for my vocal mic, attached to my 2nd tier on my keyboard stand.
Ricardo Reyes Mendez
2025-03-16 15:40:47
Buen producto. Funcional
Aubrey
2025-03-08 09:35:51
I have been looking for something like this for a while. I can attach my iPad and the top part of a mic stand. No more added mess around the stage. Perfect!!!I was so happy with it that I immediately ordered a second. My only regret is that I didn't order four from the beginning. I'd love to have two for my studio and two for gigging. At that price, why not?
カスタマー
2025-02-16 15:52:44
ã¨ã¦ã‚‚便利ã§è³¢ã„é“具。ã“ã®å…ˆã«ä»˜ãアタッãƒãƒ¡ãƒ³ãƒˆã‚‚ã‚‚ã£ã¨å¢—ã‚„ã—ã¦æ¬²ã—ã„。例ãˆã°èœé¢å°ã¨ã‹ã€‚
Cris
2025-01-30 10:52:38
This attachment does what it is supposed to do well and at a great price. It attaches to the stand firmly with no slippage. It holds a laptop tray stable as long as the thumbscrew for changing the adaptor from threaded to u-mount is screwed tight.I would however recommend that potential buyers consider the height of their keyboard on the tier under the stand before they commit to the purchase. It really is quite short, so I am unable to mount my laptop on the stand above my electric piano at all and whilst I am able to mount it above my midi controller it does obscure a number of the controls.
Derek L. Elton
2025-01-21 15:04:47
Just the job for removing clutter on stage and preventing the over excited band members from kicking your mic stand over - - they do you know - but then perhaps they don't like my singing. Well they have to put up with it now they can only knock the boom arm sideways - - they do that too - - and I can rescue that without missing a beat. I had to source the boom arm elsewhere. It would have been good to have one on offer with it.
Recommended Products
