Your cart is empty.
Your cart is empty.
Features:
Size: 2 Inch
Material: Metal
Surface Treatment: Heat treatment
Number of Claws: Two-claw
Features:
- Made of carbon steel, the point of the mandrill through a special heat treatment process, more solid and serviceable.
- Adjustable design, two jaw with adjustable clamping depth, fit for different size gears and bearings.
- Comes with hexagonal screw and thread for fastening, high strength.
- Easy Performance. Use the two jaws to catch the bearing, rotate the mandrel with the thread, slowly pull out the bearing of the shaft.
- Widely use in various bearings that are not easy to disassemble.
- Suitable for automotive flywheel, motorcycle wheel, car wheel, scooter motorcycle bearing and gear and so on.
Pull Size: 35 x 45mm
Open Width Range: 15 - 40mm
Open Maximum Depth: 45mm
Product Weight : 235 G / 8.29 Ounces
Product Dimensions (L*W*H) : 90*70*28 MM / 3.54*2.76*1.10 Inches
Package Weight : 260.0 G / 9.17 Ounces
Package Dimensions (L*W*H) : 95*95*55 MM / 3.74*3.74*2.17 Inches
Package Include:
1 x Two Claw Puller
Lee K. Sachs
2025-08-20 09:12:56
The media could not be loaded.
jimmy
2025-08-01 17:50:50
Unusual product making pulling action easier
Bork Puppison
2025-07-19 13:15:28
I had a single commutator to rebuild, and it worked. If you're doing more than one, get a machined puller instead. This cast design is extremely lose and has no flat faces to grip with, so it ends up slipping around a lot before actually applying tension.It is super inexpensive if you just need it once, though. Just expect to put up with the screw walking and wearing itself down uncontrollably.
FredM2
2025-07-15 12:14:56
This puller is well made of sturdy metal pieces that should last a lifetime. I used it to take the bearings off the motor of a battery powered grinder. It is adjustable to hold on to the bearing and it works great. Not like the cheap bent flat metal pullers that make using difficult. A handy addition to any tool box.
Thomas P.
2025-06-12 17:11:23
I've bought a lots of tools that I will probably use one or two times in my life. To save a little money I will sometimes buy items made in China. This gear and bearing puller was the WORST piece of crap I've ever received. I was working on a deadline and didn't have time to wait for a replacement thought I doubt it would have been any different the second time around. One of the "jaws" was a full millimeter longer than the other. The crossbar had only been finished on one side, so the jaws wouldn't slide all the way to the center like they are suppose to. I actually had to take the crossbar to my grinder and remove cast iron until I could get the jaws to center and reduce the top surface enough that the jaws were aligned. Granted, it only took about 10 minutes to get it ground down and trued up enough that is was "usable". The center screw came with a point on it. After pulling the first 16mm x 10mm pully from a 5mm shaft, the "point" was now about 2mm across. After the second pully it was at least 3mm wide! I don't know what grade of steel they used, but it was VERY soft. Really total junk after two small pullies!!
Mike
2025-06-06 17:30:40
The reason I bought this gear puller was because the other common small gear puller sold here is aluminum and several reviews show it breaking apart upon use.I knew when I bought this I'd have to do some work to it, I just didn't know exactly what. Please refer to the pics. The good thing is that this is made from steel and should hold up under pressure. The bad thing is that it's basically hand made and suffers from very very rough forging. What I wanted this to pull is small pulleys on my 3D printer. Due to the inexact forging it does not close up to a small diameter evenly. The metal is "blobbed" out too far on one side of the center screw. This prevents one side of the jaws from getting to the same distance as the other side close-in. I can only imagine the poor soul making this thing in some sweat-shop.To fix it I got out my grinder and vise and went to work. I worked on it for about 20 minutes until I got the "blobbed" out side cut back so it would allow the jaw to close in like the opposite side. I also cleaned the threads (M10 x 1.5) of burrs with a tap and die.This fixed it to my satisfaction. All I need to do now is re-paint it. Giving a rating of 3 due to poor quality control.
JUAN A GALVIS
2025-06-03 13:30:32
Needed to replace a bearing at the end of an electric motor. Made pulling the old one off the shaft super easy and without risking damaging anything.
Odie M Kivarkis
2025-05-01 11:03:22
I used the tool to extract a very stubborn gear from its press-on shaft and it did it very well. However, the threaded post was slightly short and it ran out of thread before complete extraction, so I had to add a small shim to compensate for the lack of length of the post.As a side question to this is: why Amazon doesn’t make Prime on all its shipments? Just before this item I ordered one that was not Prime and I was charged $19 for shipping when I am paying $14.99 per month for prime subscription?
noel b.
2025-04-24 14:27:23
ce produit est conforme a mes attentes.
Jose
2025-03-31 10:56:56
Muy bueno cumple su función perfectamentelo volverÃa a comprar
Helicopter
2025-03-09 11:35:54
Pour déposer roulements moteur électrique (perceuse,taille haie scie sauteuse etc)Je conseille à l’achatCdlt
enrico castravelli
2025-03-01 15:16:51
non sono stato capace di estrarre niente, perche gli angoli interni per la presa sono arrotondati , di conseguenza scappano
ümit akan
2025-01-23 11:35:13
Kaliteli
Recommended Products
