Your cart is empty.
Your cart is empty.Product Description
- Metal table legs for the home office are functional, sharp looking, sturdy legs at reasonable prices and built to handle heavy loads.
- They make great replacement table legs in the home office, desks or even kitchen tables.
- Great for tables, desks, counter tops, kitchen tables. Easy to install.
- These metal table legs are functional, sharp looking, sturdy.
28 Inch Adjustable Metal Furniture Legs
- 4 x Desk Legs, 20 x Long Screws, 4 x Mounting Plates
- Max. height 737mm/29"
- Mini. height 720mm/28"
Details
Material: Strong Metal
Its surface is treated by electrostatical spray and is odorless.
Weight: 1.87LB/0.85KG (One Leg)
One single leg holds up to 220 lbs.
Diameter: 2"/50mm
These legs are heavy duty and durable.
Height: 28"/720mm
These legs have nice clean lines and are adjustable about an 1".
Application
Customer
2025-08-24 14:31:59
The legs are built well and look nice. My son used them to hold up his counter top pc game gaming system. The height is perfect and he easily installed them himself at 13.
David F.
2025-08-21 15:11:13
I bought these legs for a homemade desk using a 6’ x 2.5’ butcher block counter from Home Depot. I was a little worried these would be too flimsy or that the desktop would be too heavy, but I was very pleasantly surprised. The desk feels very sturdy and holds the weight of monitors, desk trinkets, and my wrist/arm weight while typing. It’ll wobble slightly when I try to push it, but what desk doesn’t?Installation was super easy and the adjustable feet make it easy to ensure a stable and level experience if you have uneven spots in your flooring. Will buy again.
Larry Klein
2025-08-16 13:34:32
This is the third set of these legs that I’ve used. They are very sturdy and look great on my tables. Definitely a good buy!
Marc
2025-08-13 10:57:16
(QLLY 27.5 inch / 70cm Adjustable Tall Metal Desk Legs, Office Table Furniture Leg Set, Set of 4 - 70cm, Black / $40 for 4pcs at the time of ordering)Made a large desk out of butcher block and 2 Husky tool chests (one on each side). The butcher block was pretty big so, there was about 18†of table hanging off the back of the tool chests. The height of each chest was 27.5†and that leg height was surprisingly hard to find. Most of the ones I came across were 28â€. I did initially try some 28†legs with some 1/2†plywood on top the Husky’s but it just looked sloppy and forced. Then I came across these.The 27.5†height was absolutely perfect. And the fact that it was adjustable was even better. The included screws were a little small. I did end up using some beefier screws (shown in pic) as the tabletop was thick enough to allow for it. But if the desk top had been thinner, their included screws would’ve worked fine.Assembly is easy. The legs come in 2 parts. Just twist the round base onto the leg and you’re all set. Both parts tighten together nicely. Then just attach it to your desk. I love that there were 5 screw holes for increased support. 2 of these legs behind the tool chests gave me the stability I needed for this 6ft+ desk. Couldn’t be happier with how it turned out.
robert visicaro
2025-07-18 18:11:16
These legs worked great! Needed legs for a live edge maple slab that i wanted to build an end table with. Easy to install and awesome that they are adjustable.
Tom123
2025-06-18 14:29:04
28 inch Adjustable Metal Desk Legs.1. I mounted onto a 2.5’x 3’ ¾†finished plywood. Each of the four legs and brackets had a decent black paint coating.2. Each leg was individually wrapped in a plastic sleeve. The four brackets were in one bag which also contained a smaller bag holding the mounting screws. The whole set was in a square long box with padding on each end.3. Mounting brackets were not warped so mounted flush. The threaded rod for the legs was the appropriate length (if threaded rod was too long, it would not allow leg to seat fully into bracket when mounted – one reviewer commented on poor fit of legs into bracket).4. The threaded rod for each leg had light coating of paint. So the rods threaded snugly into bracket without any wobble. I test fit each leg into a bracket to ensure a snug fit, being concerned over that one reviewer’s comment about not being snug. Recommend you do same as if they are not snug, you’ll want to know before you mount the brackets. You’ll probably need to remove the leg from the bracket before mounting the bracket to your table, unless you have Popeye wrists and install screws manually or have some special joint on your power drill. I used a 3/32†drill bit to pre-drill holes for the mounting screws. You’ll probably want to mark maximum depth on your drill bit so you don’t drill all the way through your table. I used painter’s tape.5. There are five screws per bracket. They are a smidge over 5/8†long with Phillips head. The set came with 21 screws (one spare provided which I appreciate). Screw heads were not rounded when I installed screws into brackets with a power driver.6. Each leg is adjustable after installation by means of a threaded foot on floor end.7. The set came with no instructions. Seems intuitive, however, you know what they say about assumptions.8. Price was reasonable compared to what I saw in the big box store, where they sold the legs and brackets separately and at higher cost.9. The finished table is quite stable. I wouldn’t stand on it, but it’s fine for a desk.10. The legs go straight down from mounting bracket.
Jane
2025-05-16 10:40:21
Sturdy. Good for homemade table. Easy to assemble. There are height differences available too!
Most Interesting
2025-04-21 19:30:42
I recently received 4 22" legs and this is the fourth set of QLLY legs of this size I have purchased. They look great and I have now attached them to a table I made and they work perfectly.
Random
2025-03-21 13:23:40
I received 2 out of the 4 legs with the welded joint broken. The rest of the description matches - an adjustable screw allows to adjust height. The quality is lacking though - they didnt remove the rust before welding.
Jérôme
2025-02-05 10:08:00
Sur les 4 pieds reçu j'en ai un qui est déjà abimé, il y a un coup sur le tube et le filetage qui permet de fixer la plaque et déjà dessoudé.
カスタマー
2025-02-01 15:45:29
見ãŸç›®ã¯ã‚ˆã—ã€ã—ã‹ã—座金ã¨è„šã®ãƒã‚¸éƒ¨åˆ†ã®å‡ºæ¥ãŒæ‚ªããƒã‚¸ãŒèˆã‚ã‚‹ã€ã“ã‚ŒãŒ4本ä¸å…¨éƒ¨ã€‚何ã¨ã‹å–り付ã‘ã¦ã‚‚è„šã®åº§ã‚ŠãŒæ‚ªãã¦å¤©æ¿ãŒã‚°ãƒ©ã‚°ãƒ©æºã‚Œã¦ã‚‚ã†ã€ãªã‚“ã¦è¨€ã†ã‹ã€‚強度ã£ã¦ãªã«ï¼Ÿ
Dani
2025-01-29 15:29:57
En la medida que necesitaba, habia muy poca opcion.Estas patas no son precisamente baratas, pero son muy gruesas y robustas.Aguantan un aseo colgante que empezaba a dar problemas.Muy muy recomendables.
sameer
2025-01-12 15:19:32
It’s a good and strong metal product . It will be more better if it have rubber at the bottom than the plastic.
Recommended Products