Your cart is empty.
Your cart is empty.High Quality Spring Clips for hose air hose, water pipe, automotive fuel line, silicone hose, etc. Material: 65Mn Spring Steel Packing quantity: 72pcs Package included: 10 x 6mm-----------------------------10pcs 10 x 9mm----------------------------10pcs 10 x 10mm----------------------------10pcs 10 x 12mm----------------------------10pcs 10 x 14mm----------------------------10pcs 10 x 15mm----------------------------10pcs
slingshot1961
2025-08-18 18:49:38
I like the quality of the clamps and plastic organizer box. Nice selection of sizes.
Boojie2000
2025-08-12 11:12:21
I really only needed the 1/4†clamps. However for the money, I just could not pass up this kit. I was always reusing old ones. Sometimes the old ones I was taking off would break and then I’d use small screw type clamps which are much bulkier and an eyesore. Now I have a major assortment , and am very happy with the kit. I have already used two 1/4†clamps and they went on easily and clamp my fuel hose perfectly.
Customer
2025-08-10 13:09:00
I wasn't sure what size of clamps I needed for the oil cooler lines on my van, so I got this whole set of various sizes. They are not as thick as the OEM clamps, so I doubled them up with the clamps side to side on each hose fitting. Even if one fails, there is a backup on all 4 hose connections for the transmissions oil lines going to the radiator. So far, no leaks or seeping at all.The second to largest size clamp was perfect size for my 3/8" Gates ATF hose.With that all said, if there wasn't room to double up the clamps, I would be nervous of their durability or tightness if only using one clamp at each hose fitting. Probably work best as clamps for lower pressure hoses or vacuum hoses. Some automatic transmission cooler lines can see upwards of 60+ PSI at times, but normally below 30 PSI.
Talltexan
2025-08-08 10:13:42
These spring type hose clamps come in several different sizes and that’s the main reason I got this set because I didn’t know what size I would need when replacing the gasoline shut off valve on my generator. I chose this style clamp over the screw type clamps because it’s installed in an area where there in not a lot of extra room. With these clamps, they can be put on the hose and once the fuel line is slipped on the fitting all you have to do is squeeze the clamp with needle nose pliers and slide it into position and release it and you are done. They are quick and easy to install and appear to be made of high quality material that has an alodine treatment that protects the clamp from rust and corrosion. I would buy the set again if I needed more clamps of this type.
JAMES L.
2025-07-18 14:48:00
Good variety set to have around, good quality
Vallejojoe
2025-06-13 13:42:01
These are very good spring clamps. They worked well for my application and are holding very well. I considered returning them as the sizes did not go up to the size I actually needed the most but because they worked so well I decided to hold on to them and order some larger ones to complete my project. Not sure about some of the negative ratings. I know they can be a little difficult to open and hold open which may be why some broke in some of the reviews. I went ahead and purchased the Hose Clamp Plier to make it easier to install the clamps, $9, can't beat that and they worked well. The right tool for the job can eliminate a lot of frustration.
Rumen Deyanov
2025-06-07 12:08:09
On theory, a good selection of various diameters clamps. The right material (spring steel)is used, have decent anti-corrosion protection (looks like cadmium plated clamps), good number of various diameter clamps are offered. The main issue with these clamps is the ratio between the clap diameter and clamp material thickness. In simple words, clamps are made of too thick material for their diameter. Why is that a problem, you may ask? Well, the problem is that due to the too thick material, when we are installing them over the hose, by opening them with pliers to increase their diameter, in most cases these clamps experience plastic (permanent) deformation, even if it is not so obvious, once installed. In more technical terms, the clamp material yields, goes into plastic deformation zone and they either lose shape, or brake altogether, as indicated in some other reviews.Please see the attached photo for illustration purposes The clamp on the left is a well designed clamp (not from this order) with proper thickness (not too much) and it does not yield when installed, as it is more flexible, in lay terms. The clamp in the middle is unused, never installed 10mm clamp from this order. The clamp on the right is the same size clamp, which has been installed on a 10mm hose once. You can see that the installed clamp has permanent deformation and has lost its round shape, which means it is not doing its job as well as it was designed to.Apologies for the longish review, but did not have enough time to write a short one :) All the best!
David kirchner
2025-05-21 16:31:32
These in a variety pack are handy for leaky tubing on hydration bladders, fuel lines, i believe good quality way to seal up tubing!
Customer
2025-05-04 17:42:05
Seems to do the intended job. No special tools required, just need some needle nose pliers
Customer
2025-02-13 11:50:13
They are what they are and work very well for my intended uses.
Justice :)
2025-02-03 16:19:46
there ok but could be a bit better :) but still does the job
Richard Egan
2025-01-08 11:44:42
Perfect for the oil lines and fuel lines on a seadoo that I’m rebuilding
Anthony Boese
2024-11-27 15:02:01
Great little clamps, used themFor the hoses on my motorcycle. Really strong and rigid. Almost needs a little tool to depress them. They killed my fingers trying to pinch and slideThem
Recommended Products
