Your cart is empty.
Your cart is empty.Riri
2025-09-06 11:31:53
Worked as designed
Jonnyboy
2025-08-24 10:28:11
Nothing to dislike. It fits most manufacturers overhead extractor fan filter housing. extremely simple to install and it works great.
Gloria N.
2025-08-10 15:00:15
Fits perfectly and took 5 seconds to replace. Question? Where do you buy the black material that fits inside the metal mesh?m
Patrick Haire
2025-08-07 14:58:57
Worked out fine
Trina W.
2025-08-01 16:56:32
Finally found the right replacement. Very satisfied with the quality and thickness. Will definitely buy again when I need another one
C. M. P.
2025-07-28 13:05:46
Contacted the Rangeair company for the best replacement filter & they were spot on
Haelley
2025-07-21 17:12:42
LEARN FROM MY MISTAKE! I didn't read the individual reviews and wish I had. I don't know if its their manufacturing process or poor verbal translation, but the measurements are off making this an utterly sloppy fit. These look good when you open them, as pictured online, but the filter doesn't "pop/click" into place like it should so when you turn the fan on it lifts on at least one side allowing the unfiltered air to go right past the "filter". The frame thickness is as advertised, but the actual thickness of the filter media itself is rather thin and the charcoal media is actually a waste considering my range hood vents to the outdoors. The build quality is flimsy and it felt like it was going to distort/bend during installation. It does NOT work well on any level whatsoever!!
Sandyman
2025-07-19 14:00:58
Meets the purpose fit, and value criteria. Very helpful. This replacement was otherwise very hard to find.
Customer
2025-07-09 17:46:04
The listing seems to imply this is a 2 pack, but they sent 1. It was just a hair too small to sit in my fan without falling, but a little duct tape did the trick and it is installed and working fine. Such a relief to have my gross old filter out of here.
Riri
2025-06-23 15:18:36
Worked as designed
Jonnyboy
2025-06-16 18:02:15
Nothing to dislike. It fits most manufacturers overhead extractor fan filter housing. extremely simple to install and it works great.
Gloria N.
2025-06-15 14:28:32
Fits perfectly and took 5 seconds to replace. Question? Where do you buy the black material that fits inside the metal mesh?m
Patrick Haire
2025-05-24 13:55:57
Worked out fine
Trina W.
2025-05-15 10:13:45
Finally found the right replacement. Very satisfied with the quality and thickness. Will definitely buy again when I need another one
C. M. P.
2025-04-09 11:45:26
Contacted the Rangeair company for the best replacement filter & they were spot on
Haelley
2025-03-17 10:14:26
LEARN FROM MY MISTAKE! I didn't read the individual reviews and wish I had. I don't know if its their manufacturing process or poor verbal translation, but the measurements are off making this an utterly sloppy fit. These look good when you open them, as pictured online, but the filter doesn't "pop/click" into place like it should so when you turn the fan on it lifts on at least one side allowing the unfiltered air to go right past the "filter". The frame thickness is as advertised, but the actual thickness of the filter media itself is rather thin and the charcoal media is actually a waste considering my range hood vents to the outdoors. The build quality is flimsy and it felt like it was going to distort/bend during installation. It does NOT work well on any level whatsoever!!
Sandyman
2025-03-13 18:46:40
Meets the purpose fit, and value criteria. Very helpful. This replacement was otherwise very hard to find.
Customer
2025-02-19 13:03:52
The listing seems to imply this is a 2 pack, but they sent 1. It was just a hair too small to sit in my fan without falling, but a little duct tape did the trick and it is installed and working fine. Such a relief to have my gross old filter out of here.
Recommended Products