Your cart is empty.
Your cart is empty.This TCI TV Cable Correct Kit for Quadrajet/Edelbrock/Carter Carburetors ensures the correct line pressure for the best performance and service life from your GM 2004R/700R4 Transmission.
221
2025-07-05 11:37:34
interferes with a runner in the 2101. well made but doesn't fit. i'll have to cut it up and weld on a second tab to make it work.
Wasn’t wide enough had to modify otherwise good
2025-05-27 13:07:27
Didn’t fit Holley base
Eugene Baker
2025-05-26 18:34:57
Yes correct item for 700r4 on Chevy 350, Edelbrock. But depending on age and originality of vehicle be prepared to modify the bracket to suit any alterations made to the vehicle. Installed onto 71 Chevelle wagon, 2003 350 Vortec, Edelbrock AVS2-650, conversion from Quadrajet to Edelbrock. Had to add an extension bracket plus drill hole for Dakota cruise control cable.
Ian M.
2025-05-02 17:19:47
Not compatible with Edelbrock 1406 and Edelbrock Performer manifold.First problem: must use inner bolt holes on carb. About half of the Edelbrock manifold allow this. Luckily mine was one of them, yours might not be.BUT... once you get past that hurdle, you’ll find that the bracket won’t clear the intake on the back side unless you’re using a riser.THEN, you’ll find that even with a riser, the geometry of this bracket will be waaaayyy off track. And yes, I have a geometry corrector installed on the carb itself. Bracket locates cable about an inch too far inward.AND FINALLY, you’ll discover that you can only use this bracket if you’re using a cable actuated throttle pedal. If you use a throttle rod and linkage, like I do, the rod will not be compatible with this bracket. You may be able to cut off the upper part of the bracket to make this work, but I opted to return this item instead due to all its other flaws. This is a steaming pile of junk.Most other reviews I read online only mention the problem with the inner bolt pattern. I hope this review steers people clear of this item who think that’s the only problem with this bracket.
Paul Ardolina
2025-04-25 15:29:44
Excellent fit and finish.
phil
2025-04-02 13:48:50
DOES NOT FIT Edelbrock AVS carbs, 100% does not fit. good quality bracket but DESCRIPTION IS WRONG might fit Edlebrock carbs, but not AVS models
michael zalesky
2025-03-26 14:22:31
Took off a Holley carb and went back to the original GM style 4 barrel, qjet so we needed a different bracket than the Holley. Quick ship, next morning it was on my porch. Installed and worked great.
iWorkHard4My$
2025-03-10 10:37:03
Looks good have not installed yet
MykDelta
2025-02-04 10:00:29
I swapped a th200 trans for a built 700r4 I only realized as I got going that I would need a bracket like this. Fortunately I found the tci one on here and it works great only cost $55 at the time. My shifts are crisp and everything works great.
Mark Rust
2025-02-03 18:33:28
After waiting a very long time for this bracket the holes did not line up like advertised. Had to cut and modify.
Mike
2025-01-27 13:49:07
Fits good looks like it will work well project not finished yet
Jeff
2025-01-11 09:34:23
Works well for quadrajet carbs too.
Gordon A.
2024-12-10 10:17:09
It definitely doesn't fit as advertised. It doesn't fit an Edelbrock carb nor will it line up with the carb linkage. Unfortunately I can't return it because I already painted it. I will either have to cut it up and modify it, or consider it a total waste of money. Don't buy this item.
Recommended Products
$42.90
$ 22 .99 $22.99