Your cart is empty.
Your cart is empty. IR emitters are small connected transmitters that send an infrared signal from your remote to a separate piece of audio/video equipment. It is available in single or dual emitter packages, one of which emits the same signal through two distinct housings. Our dual-head infrared emitters blink in both visible and infrared light and are utilized to transfer data to a single component source. This IR Emitter allows you to send infrared signals to areas where your remote control or IR repeater system cannot. You can place this emitter in challenging locations and work around obstacles like media cabinets and displays. These IR emitters contain a self-adhesive pad that can be applied directly to your AV device's IR sensor window. The length of the IR wire is ten feet, and you can separate it by gently pulling the heads in opposite directions. The connection comes with a mono plug measuring 3.5 mm, making it simple to plug into your device. It has a sticker that adheres to the back and can be placed directly on various devices. It is also possible to position the transmitter end several inches or even a few feet away from the receiver. For example, it could be concealed on the interior of a stereo cabinet door or shelf.
SN
2025-09-02 17:26:43
Works well. Installed it for my epson 6040ub which now starts and switches off via the harmony hub without skipping.
joe
2025-08-31 10:20:20
Had to reset my samsung remote
Mr PC Parts
2025-08-16 11:28:25
Did not control 3 devices on my system. Had everything setup for 3 devices, even had a two emitter cable control my 3 devices most of the time (it would sometimes not turn off TV). They were all setup on the Xbone fine, though this wouldn't work with any device, even tried to reconfigured Xbox, still nothing. Went back to two emitterr device because this didn't control my 3 devices: TV, Cable Box, Surround Sound.Let me be clear, my two emitter device controls the Cable Box, Surround Sound perfectly, it only sometimes doesn't turn off the TV when turning off the Xbone. When turning on Xbox, it turns on ALL THREE devices just fine with my two emitter device. This product wouldn't signal ANY of my devices. Sticking with the two emitter and simply turning off TV with cable remote. refunding this.
JohnR
2025-08-13 13:55:14
This worked perfectly with the OREI Wireless HDMI Transmitter Receiver Extender 1080P Kit with IR Remote that I purchased to view AV from components too far for quality viewing. The IR receiver that came with the unit had a cable that was too short for me to properly position the Wireless HDMI Transmitter and still control the system components. I attempted to use other cables to extend the original, but none worked. The TNP IR Emitter Extender Extension Cable paired well with the OREI Wireless HDMI Transmitter and I am able to easily control the two system components in the living room from the bedroom.
DJ
2025-08-06 17:53:35
Well built little extender cable. Works perfect as an extender with existing IR transmitter (Blumoo) which can't directly beam to components because it doesn't have a direct line-of-sight to the components. Those components include a TiVo, Yamaha Receiver and Sharp TV. IR emitter transmitters don't have to be placed directly on the device IR receiving sensor but in line of sight a few inches away. I use a flashlight to locate the IR sensor on each component. It's usually a little round hole somewhere on the front surface of the component. I then use bluetac to hold the IR extender sensor on the flat surface in front of or attached to the bottom of the shelf above the component. Highly recommended.
SN
2025-07-22 17:32:29
Works well. Installed it for my epson 6040ub which now starts and switches off via the harmony hub without skipping.
joe
2025-07-18 18:41:39
Had to reset my samsung remote
Mr PC Parts
2025-07-17 15:54:07
Did not control 3 devices on my system. Had everything setup for 3 devices, even had a two emitter cable control my 3 devices most of the time (it would sometimes not turn off TV). They were all setup on the Xbone fine, though this wouldn't work with any device, even tried to reconfigured Xbox, still nothing. Went back to two emitterr device because this didn't control my 3 devices: TV, Cable Box, Surround Sound.Let me be clear, my two emitter device controls the Cable Box, Surround Sound perfectly, it only sometimes doesn't turn off the TV when turning off the Xbone. When turning on Xbox, it turns on ALL THREE devices just fine with my two emitter device. This product wouldn't signal ANY of my devices. Sticking with the two emitter and simply turning off TV with cable remote. refunding this.
JohnR
2025-07-16 16:48:08
This worked perfectly with the OREI Wireless HDMI Transmitter Receiver Extender 1080P Kit with IR Remote that I purchased to view AV from components too far for quality viewing. The IR receiver that came with the unit had a cable that was too short for me to properly position the Wireless HDMI Transmitter and still control the system components. I attempted to use other cables to extend the original, but none worked. The TNP IR Emitter Extender Extension Cable paired well with the OREI Wireless HDMI Transmitter and I am able to easily control the two system components in the living room from the bedroom.
DJ
2025-06-26 17:56:19
Well built little extender cable. Works perfect as an extender with existing IR transmitter (Blumoo) which can't directly beam to components because it doesn't have a direct line-of-sight to the components. Those components include a TiVo, Yamaha Receiver and Sharp TV. IR emitter transmitters don't have to be placed directly on the device IR receiving sensor but in line of sight a few inches away. I use a flashlight to locate the IR sensor on each component. It's usually a little round hole somewhere on the front surface of the component. I then use bluetac to hold the IR extender sensor on the flat surface in front of or attached to the bottom of the shelf above the component. Highly recommended.
Hugo
2025-05-28 14:55:11
My grandma lost her remote, and we couldn't get a universal remote to work on the TV. Turns out that we needed one of these in order for the TV to pick up the signal. Universal remote is working properly now thanks to this.
Jeff Vier
2025-05-22 11:40:24
Very nicely made. Wire feels high-quality (very supple). Molded casing on the miniplug end is sturdy with a decent anti-fatigue "tail" on it. Unit comes with the 3 wires which power the emitters bonded together until very close to the emitter heads, but you just easily pull them apart to split the wire to where it works for your application.I am pretty sure I have a nonstandard use-case for this, so I'll post the details in case anyone else happens to be searching for these keywords.For my application, in my RV I have an older IR repeater (a RiverPark AVI-20 connecting block) that uses RCA (phono) plugs to connect the emitters (a.k.a. transmitters or "blasters"). Apparently no one in the known universe (including Riverpark) makes these anymore; everyone uses 3.5mm mini-plugs, now, like these. So I bought an adapter () and these emitters. I fully expected this to fail miserably. Or, at the very least, be wired "backward" to how the repeater expected it (because Murphy's Law) and have to re-wire these.Amazingly, it works *perfectly*!
RCAddiction
2025-05-20 18:42:54
I purchased this along with the to use with my Logitech Harmony Smart control. It plugs right into the rear port of the Logitech Hub, and works well on my Onkyo Receiver, LG Blu Ray and Verizon Fios STB. Having read reviews on similar IR emitters, I knew this one fires the IR out the front, not through the bottom. So, using the included tiny self stick pads (would be great if it came with extras), I adhered each emitter to the face of each device, adjacent to, (not on top of) the IR sensor on each device.Works really well, and solved my issue with distributing the IR to multiple devices inside my BDI audio cabinet.Make sure you buy the Monoprice, (or similar) adapter linked above or the 3.5mm plug will not fit into the Logitech Hub.
Lee
2025-05-16 13:31:20
This is just what I needed for my Xbox One. Plugs in easy and works as required.All in all – Good product
hs
2025-05-15 10:19:53
preiswert/funktionel als ok.
crazyvolz
2025-05-02 21:45:14
Produkt TIP TOP
A Hovestad
2025-04-24 16:18:36
Niet geschikt voor tv ontvanger Canal Digitaal.
Armin D.
2025-03-14 19:12:46
Das gelieferte Produkt entsprach nicht der Produktbeschreibung. Es wurde ein IR-Emitter mit USB-Anschluss geliefert, welcher nicht mit der X-One kompatibel ist.
Hugo
2025-03-02 12:12:47
My grandma lost her remote, and we couldn't get a universal remote to work on the TV. Turns out that we needed one of these in order for the TV to pick up the signal. Universal remote is working properly now thanks to this.
Jeff Vier
2025-02-11 13:25:52
Very nicely made. Wire feels high-quality (very supple). Molded casing on the miniplug end is sturdy with a decent anti-fatigue "tail" on it. Unit comes with the 3 wires which power the emitters bonded together until very close to the emitter heads, but you just easily pull them apart to split the wire to where it works for your application.I am pretty sure I have a nonstandard use-case for this, so I'll post the details in case anyone else happens to be searching for these keywords.For my application, in my RV I have an older IR repeater (a RiverPark AVI-20 connecting block) that uses RCA (phono) plugs to connect the emitters (a.k.a. transmitters or "blasters"). Apparently no one in the known universe (including Riverpark) makes these anymore; everyone uses 3.5mm mini-plugs, now, like these. So I bought an adapter () and these emitters. I fully expected this to fail miserably. Or, at the very least, be wired "backward" to how the repeater expected it (because Murphy's Law) and have to re-wire these.Amazingly, it works *perfectly*!
RCAddiction
2025-01-26 16:15:32
I purchased this along with the to use with my Logitech Harmony Smart control. It plugs right into the rear port of the Logitech Hub, and works well on my Onkyo Receiver, LG Blu Ray and Verizon Fios STB. Having read reviews on similar IR emitters, I knew this one fires the IR out the front, not through the bottom. So, using the included tiny self stick pads (would be great if it came with extras), I adhered each emitter to the face of each device, adjacent to, (not on top of) the IR sensor on each device.Works really well, and solved my issue with distributing the IR to multiple devices inside my BDI audio cabinet.Make sure you buy the Monoprice, (or similar) adapter linked above or the 3.5mm plug will not fit into the Logitech Hub.
Lee
2025-01-11 16:08:53
This is just what I needed for my Xbox One. Plugs in easy and works as required.All in all – Good product
hs
2024-12-24 15:17:20
preiswert/funktionel als ok.
crazyvolz
2024-11-24 12:21:19
Produkt TIP TOP
A Hovestad
2024-11-23 13:08:18
Niet geschikt voor tv ontvanger Canal Digitaal.
Armin D.
2024-11-20 13:46:49
Das gelieferte Produkt entsprach nicht der Produktbeschreibung. Es wurde ein IR-Emitter mit USB-Anschluss geliefert, welcher nicht mit der X-One kompatibel ist.
Recommended Products
