Your cart is empty.
Your cart is empty.These 5/8 inch diameter ball bearing rollers are perfect for creating your own out feed roller tables. Unlike rollers which operate only in a straight line, these 360 universal transfer bearings are particularly suited for curved work created on band saws and router tables as well as straight cutting on bench saws and miter saws . Featuring two screw holes in each bearing surround for solid attachment to the worktable or workbench. With a load bearing of 55Lbs each, they are supplied in a set of six.
Nathaniel Moseley
2025-08-30 16:29:09
I got these little roller balls to put on the back of a pegboard I mounted to a sit-stand motorized desk, to keep the pegboard from dragging on the walls. They're reasonably small (I was looking for smaller not bigger) and are easy to work with. The screw holes are far enough from the body of the bearing to accept most any screw/bit/driver. The only issue I had was one of the six arrived with a bent tongue where the screw goes in, so I had to hammer it back into shape, but that worked fine. I'm not putting a lot of pressure or stress on the bearings, so I can't comment how well they function as bearings, other than that they are smooth and relatively quiet. I can hear them under the electric motor that raises my desk, but only barely.
R. A. Williams
2025-07-27 11:19:52
I needed some roller bearings for an invention and bought these. They are very easy to install (two screws will do it) although they are designed primarily to withstand vertical load. The ears of the housing are less sturdy and not designed to absorb lateral force. I found the operation of the bearings to be smooth and easy. These are quite fun to use and play with. I may buy more to have around the lab.
Rbwindowdesigns
2025-07-09 19:53:57
The media could not be loaded.
Upton O'Good
2025-07-04 10:26:09
Used these on a diy rock/brass tumbler to run up against the barrels to keep them from moving. Works great bolted to a piece of flat steel. haven't needed to even oil them over many hours of operation.
Kindle Customer
2025-06-27 11:11:47
5 Star, We put all twelve of these on 1/2" plywood that is supporting an empty wine barrel to be used as a table. We have the need to move it due to where we keep it. Right now this has been the perfect solution for us. We are happy. Getting ready to close up deck area for winter...but as you can see we had a piece of 1/2" plywood cut, corners trimmed and varnished. Attached two paks of the rollers (12) on bottom for stability and now we can move it as we need to when we entertain on the deck. Couldn't be happier!!
Paul Cola
2025-06-21 15:21:26
Not sure if the balls are imperfectly round or if it's just the whole metal-against-metal thing, but after installing them on the bottom of a board that is acting as a shelf, we noticed they are quite clunky sounding and noisy.To be fair, they're cheap and they do work, but don't use them when the baby's asleep or when someone is disarming a bomb near you. I think the more weight they have on them the more noise they make. Functional, practical, but not quiet.
A.J.
2025-05-28 16:27:40
I velcrowed these to the bottom of my 4 gallon shop vac. They roll rather well. The shop vac is only about 10-15 pounds empty.
Hoss0001
2025-05-20 13:48:22
noisy and sticky
Bernard
2025-04-20 12:05:32
bearing perfectly for my needs
Wayne Martin
2025-02-20 17:44:20
Table saw outboard support table.
michel lacas
2025-02-09 18:46:19
Plate forme roulante
Tom Lloyd
2025-01-21 14:56:51
a little small for my needs only received half my order
alain bilodeau
2024-12-24 17:13:25
Pas utiliser les piece non pas les mesures décrite sur l’annonce
Recommended Products
