Shopping Cart

Your cart is empty.

Your cart is empty.

uxcell 12pcs 600 Grits Abrasive Mounted Stone 2.35mm Shank 1/4'(6mm) Dia Pointed Point Heads Stone Grinding and Polishing Wheels for Nail Polishing

4.3 (6) Write Review
Free shipping on orders over $29.99

$12.09

$ 5 .99 $5.99

In Stock

1.Color:Black


2.:80 Grits


3.:12


About this item

  • [ Size ] - Shank Diameter: 2.35mm/1/9", Head Diameter: 6mm/1/4", Total Length: 48mm/1.89"; Grinding Head Material: Silicone, Diamond Sand.
  • [ Material ] - Silicone material, corrosion-resistant, good heat dissipation performance and stability. Silicone grinding head is made of diamond powder and silicone, the material is very fine and soft, and can only be used to grind very smooth surfaces
  • [ Applications ] - It can be used for polishing gold and silver jewelry, polishing nail polishing, jade polishing and other soft materials, and polishing high hardness materials
  • [ Usage ] - Can be installed on electric tools such as grinders, and grinding machines for deburring, surface grinding, sharpening, polishing and time-saving.
  • [ Notice ] - Flying chips may be generated during use. Please use jigs, non-slip finger stall, and wear protective glasses when using this corundum grinding bit.


Product Description

Dremel Rotary Tools

Specification

  • Color: Brown, Black, Gray, Pink, Blue, Light Blue, Green
  • Granularity: 80, 120, 150, 180, 600, 800, 2000
  • Shank Diameter: 2.35mm / 1/9 Inch
  • Heads Diameter: 6mm / 1/4 Inch
  • Head Length: 16mm / 0.63 Inch
  • Overall Length: 48mm / 1.89 Inch

Tips:

  • The new corundum grinding bit should be tried at a low speed before use. If there is a jumping problem, do not continue to use it.
  • Please press gently and avoid shaking. The corundum grinding bit is used to grind workpieces.
  • Flying chips may be generated during use. Please use jigs, non-slip finger stall, and wear protective glasses when using this corundum grinding bit.

Richard R.
September 3, 2025
This item is not built properly. The abrasive part is attached to the shank, off-center. What happens when You use them is only 1/2 (one side) of the abrasive part touches the thing that You are grinding. The result is it bounces along, doing the opposite of the desired effect. It certainly does not do what it is supposed to!Luckily, they are so brittle and cheap that they do not cause irrepairable damage to whatever You are working on, instead, they just crumble and fall apart. Using this part was a big dissappointment. I don't consider it a waste of money because I learned not to trust the manufacturer, and stick to well-built products.
myron hanewinckel
August 28, 2025
I thought these would be like stone, but they’re not they’re soft and they disintegrate very quickly
D.C.
August 10, 2025
I bought these to try to get a smoother finish on a surface I was grinding in the lathe. These are not rigid stones though, they are like a rubber compound with grit in it. They work fine for polishing, but weren't what I was looking for. Make sure you have the right size collet when using these too. They aren't an 1/8" shank.
Ramses Osirus
April 12, 2025
I didn't realize these were rubber, I needed and expected a stone like material.
gregory doolin
December 22, 2024
I thought theis were hard hard { stone } . not rubber . please learn to write English !!!!!!!!!!!
Tom
December 14, 2024
Useless in the USA.