Your cart is empty.
Your cart is empty.Product Description
Features
- Key-less: Self-tightening key-less features automatically increasing gripping force.
- Treatment: Special quenching treated key parts increases durability.
1/2-Inch Keyless Drill Chuck Has a MT2 Mount, Holds Drill Bits Up to 1/2-Inch in Diameter
- Clamping Capacity: 1/32-inch -1/2-inch (1-13mm)
- MT2 Morse Taper Arbor
- Accuracy: 0.003-inch ~ 0.005-inch (0.08~0.12mm)
- Run Out: 0.005-inch (0.12mm)
- Will hold drill bits up to 1/2-Inch in diameter
- Drill chuck mounts in the MT2 Morse Taper Arbor
- Can be used in either the headstock or tailstock
- Tightened by hand without the need for a chuck key
Drill Chuck with MT2 Morse Taper Arbor Mount
This product is perfect for drill presses or lathes spindle accepts MT2 Arbor.
Self-tightening Keyless Drill Chuck
Self-tightening key-less features automatically increasing gripping force, high reliability, and stability.
Simple to Use
Just chuck the wood workpiece in the headstock and the drill bit in the tailstock, then feed the stationary drill into the spinning work.
Bill D.
2025-07-18 11:38:03
I needed to perfection-precision clean "both sides" to get the chuck to stay in, but clean and dry plus a couple taps and stays in just fine. Works perfectly and amazingly perfectly true. Killer value!
Lee
2025-07-13 17:34:19
Bought to use in my home shop on my wood lathe tail stock. I’m ordering 2 more, one to use on the drive side and the other to replace the stock one on my ShopFox drill press. I use the USA Jacobs original at work, they are awesome but they also cost about $325. These are 1/10 the price and I would say 98% of the quality. It works flawlessly, the paws are machined extremely well, whichever Chinese factory made these is doing excellent work!
Chris
2025-07-01 14:26:02
For the money - this drill chick is near unbeatable. This is perfect for center drills. Keep it “loaded†and near the lathe, stored in a collet rack.The depth is a bit odd so longer drill bits and reamers may not work but likely shouldn’t be used in this holder anyway.Fit and finish is surprising for the money and the MT3 taper (with a tang) is well sized.
EZ
2025-06-24 17:33:50
I got tired of popping the chuck out of my drill press to use it in my lathe. This unit works great on the lathe. I measured the runout and it was VERY minimal. It had less runout than my drill press chuck so, it will be more than adequate for my needs. I wouldn't hesitate to buy one for this price. Maybe a couple bucks more than the auction sites but with Prime you get this one fast.
DBMax
2025-06-21 10:37:39
Great improvement to my stock chuck with key. Was recommended in a review for the drill press to upgrade for accuracy and spot on! Very happy with the purchase.
Squat251
2025-06-07 09:48:29
Mine is smooth, and the taper seems accurate. I did have to cut off the draw bar extension from the end to fit this to my lathe, but I figured I would when I ordered it. Seems like a solid product to me.
Denis P.
2025-05-20 13:39:46
worst chuck ever keyless but get the vice grips to tighten or loosen,,, and if the shank on your bit is like a double ended centering tool forget it bits must be flush on the end to shallow to hold them straight,,,i bought a cheep chuck 100 x better then this one save your money buy the cheep one with a key,,,
Kindle Customer
2025-04-28 09:23:58
I use this on my mini lathe. Works perfectly. Good value.
Monterey
2025-04-27 16:36:34
I was worried that the drill bit would spin in the chuck since it’s keyless. I haven’t used the chuck very much but the times that I did there was never an issue of spinning. I like that I don’t have a chuck key. It’s quicker and way more convenient.
Betty L.
2025-04-01 15:56:01
Needed a new drill chuck for my lathe, hesitant about the price being 1/10 of the local equipment dealer here in Ontario but am very glad that I did order it. The chuck is top quality and a perfect fit in the lathe. 100% pleased.
David Barker
2025-03-10 19:32:14
Very large runout, can see it wobbling severely
LC
2025-03-09 15:08:49
As presented and works well.
Wranglercowboy
2025-01-18 13:18:42
This keyless chuck with MT3 shank arrived early.I'm using it on my 1440 Tida Lathe.Seems to be of very good quality, the barrel rotates very smoothly & has a really strong grip on drill bits I'm very pleased with this purchase!I'm going to order another one for my Milling Machine.
Recommended Products
$21.14
$ 9 .99 $9.99