Shopping Cart

Your cart is empty.

Your cart is empty.

Wimberley AP-502 Replacement Lens Foot for Nikon 400 f2.8 TC, 600 f4 TC, 800 f/6.3 Z S-line - Arca-Swiss Style - Made in USA

Free shipping on orders over $29.99

$100.00

$ 40 .99 $40.99

In Stock

1.Size:Ap-452


About this item

  • Replaces the factory foot of your lens, lowering the center of gravity for optimal balance
  • Adds a built in double dovetail for Arca Swiss compatibility
  • For Nikon Z 400 f/2.8 TC, 600 f/4 VR S-line, and 800 f/6.3 VR S-line Lenses
  • Anodized 6061 Aluminum, stainless steel fasteners
  • Made in USA. Assembled in Charlottesville, Virginia


About the AP-502 Replacement Lens Foot The AP-502 replaces the stock foot on Nikon Lenses (See list below, Image of compatibility chart, or our site). The AP-502 is precision machined to slide right into an Arca-Swiss style quick-release clamp. It also has 1/4" and 3/8" tapped holes for mounting to non-quick-release tripod heads and monopods. All replacement feet feature the same dual safety stops and flash bracket compatibility as our lens plates. For use on the following Lenses Nikon 400 f/2.8 TC Z VR S-line, 600 f/4 TC Z VR S-line, and 800 f/6.3 Z VR S-line Lenses Includes AP-502 Arca-Swiss Style replacement lens foot (Qty 1) Mounting Screw – M4 x 14mm Socket Head Cap Screw (Qty 4) Safety Stop Screws - M3 x 6mm Socket Head Cap Screw (Qty 2) Hex Key – 3mm T-Handle (Qty 1)Hex Key – 2.5mm (Qty 1) Not compatible with most Manfrotto or Gitzo clamps


Neil
2025-09-03 17:30:33
This is a lesser cost replacement foot which you wouldn’t necessarily expect from Wimberley. But it goes on perfectly and attaches securely. There’s not much to say about a lens foot but this one is a great fit and works with my tripod heads.
meterreviewer
2025-08-03 18:43:10
Perfect fit, as described.
j. salk
2025-07-26 11:11:25
I have been using Wimberley products for a couple of decades.This is a US company that is renowned for its high quality products as well as original designs.All their products are made in the US to assure the highest quality.If any photo related product, that I need is made by Wimberley I will automatically buy it. This is an assurance of the highest quality and solid design that will not fail and drop my expensive camera or lens.The Wimberley AP-611 is just that kind of product. One piece all metal replacement foot for my Sony GM 70-200 2.8 II lens.The low profile of the foot is a plus, because it doesn’t snag in the bag, straps or clothing. It also makes it possible to fits into smaller camera bags.Highly recommended!
Frappetoik
2025-07-25 12:06:26
This little foot does what Nikon won't do, and at an unbeatable price. Make sure you also tighten and purple-loctite the four screws holding the plate to which this makes onto your lens, then dab a touch of the blue loctite on the screw for this guy and you're off to the races. It's a very comfortable foot in the hand, and machined precisely to fit with Arca-Tech mounts. Absolutely brilliant, save for one thing:Minus one star for not including a quick disconnect socket in 2024.Everything else is magical.
DAVID GRAY
2025-07-24 11:47:41
The side screw is heaps better than the old method of dropping a thin piece of metal into filling the gap. Very sturdy.
Brian In Florida
2025-06-27 10:21:26
High quality perfect fit and easy to install.
MJR1
2025-04-03 11:47:40
The plate is very good if your just using a tripod/monopod. If you choose to carry the lens upside down by the foot its not possible because of the low profile nature of the plate.
Brandon Watson
2025-03-17 16:57:49
This has the same fit as my SmallRig Plates so I can swap this in and out of all of my tripods without having to adjust the set screws. The only issue is that I would have appreciated a small amount of thread locker installed in the screw to keep it locked to the body, but I picked up a tube for a few bucks and solved that myself. Also, the screws that prevent it from sliding out of an Arca-Swiss Quick Release plate are screws and I would have preferred the pins found in Small Rig Plates, that are spring-loaded, But in the Grand Scheme of things, neither of these nitpicks are enough to drop my rating. Excellent Product and works Beautifully.
TheBirdNest
2025-02-27 13:15:20
I use this to attach to my monopod, and it's rock solid. Plus it can stay on the lens, and takes up less space than the original foot and a quick release plate. Very happy with this.
DBS
2025-02-22 15:20:04
This foot is a terrible design. My first Wimberley. The foot doesn’t slide into the dovetail but only sits on the existing hub & the only thing keeping it in place is a badly designed screw that doesn’t sit flush! So it the screw loosens in the field, the whole thing will wobble, or worst fall off. Shocking to realise these chaps sold such crappy stuff only because of their reputation. It only requires an half-witter designer to have got it right. Other have started making such great products. Never Wimberley again. Never! Hejnar or Leofoto make fantastic products. My tirade against these badly designed products has begun.
loison erwann
2025-02-15 16:41:21
C'est wimberley... C'est nickel.
MRC_DK
2025-01-22 10:11:59
Se instala correctamente, pero es algo corto.
gigi bavelloni
2024-12-28 15:22:31
ottimo prodotto ,ma la cosa che non va bene e' che la scatola era parzialmente aperta,probabilmente non sapevano cosa farsene di questa staffa
Recommended Products