Your cart is empty.
Your cart is empty.We manufacture a wide selection of residential and commercial pumps and accessories to provide the best solutions for moving wastewater and effluent. With 100% factory testing, no one matches this level of dependability.
Bob
2025-09-07 17:11:15
Perfect match for my Zoeller M63 pump. Some say set a brick in the sump well and that’s good enough. I say no thanks, works very well and is a perfect fit for Zoeller pumps. The hose clamp allows you to tighten clamp to pvc line and lower down as one unit into sump pit. Nice!!
Workman
2025-09-06 12:33:47
This little guy raises your pump a few more inches to keep it above any settled sediment and provides an extra support for your pipe.Also purchased a Zoeller M53 1/3 HP, Screw-in Check Valve(30-0041), Inline Check Valve(30-0238), and Jackel Sump Basin(SF20) + lid for my setup.Absolutely worth the money to have keep thick debris from getting into your pump.
Patrick
2025-08-10 15:17:34
Does what is supposed to do and raises the sump pump off the bottom surface of your pit. It was too big to fit into my smaller pit, so I had to cut the pipe holder end off and attached with cable ties. Thanks to another reviewer for that tip. Since this also raised the pump in the pit, I had to remove a bunch of stone from the bottom so that the pump would sit lower and the float would cut on prior to filling over the inlet holes. Keep that in mind, if you have a smaller pit. Otherwise works great.
Phoenix2011
2025-08-02 12:49:10
I have a French drain on my house that empties into a 7-foot deep drywell. The well bottom is stone, but not necessarily even or level. Last spring, I found that some enterprising chipmunk had dumped a lot of both peanut and acorn shells into the well, along with digging out enough of the stone dust that surrounds the top of the well to get my Zoeller pump switch stuck on and continually running. The stone dust part has been fixed with concrete, but I needed to do something to raise the underside of the pump. This stand looked like the answer.It is indeed plastic, but very sturdy plastic. I have read other reviewers comment on that, and while I don't know for sure, making it out of aluminum would probably make the cost prohibitive. Unlike another reviewer, the hose clamp I received was stainless steel; the self tapping screw that was included may not have been. As advertised, it allows for putting PVC feet on the bottom, which will raise the pump an additional couple of inches or so. I put them on, as much for not sinking into the stone as to gain additional height.Assembly is simple enough, but when I had attached the PVC pipe and lifted it, I found that the front side of the stand kind of flops down. There was no factory provision made for securing the front end. Probably wouldn't be a problem going into a floor-level sump, but 7 feet down, I had no way to support it. I used some heavy duty wire ties to secure the front end and that fixed the problem. It is, by the way, the reason for 4 stars and not 5.
Bill
2025-07-01 09:01:14
This keeps my sump pump clear of debris - thank you
TR Man
2025-06-29 16:56:43
There are several reasons why I like this sump base.(1) It makes it harder for the pump to suck up rocks or other debris from the pit bottom.(2)Because the base allows you to change the height by installing custom length pvc piping to the underside of the base you can move the pump around to gain a little space with the backup (battery) powered pump,(or maybe another 120 volt unit if that's what you want. (3) It has a piping brace that you can secure to the discharge pipe to firm the installation up a bit. ....Although it is a little more pricy than other bases I have seen on offer, for me the extra money was well worth it.
Live Simple, Live Well
2025-06-10 19:06:28
Sump pumps can shake a bit. Which I guess is why Zoeller created the only sump pump stand I’ve seen that includes an arm to attach the stand to the pump.However, the attachment arm looks more like a poorly-conceived afterthought rather than something that would prevent a 25 lb. sump pump from falling off its stand.The arm is way too flimsy and too poorly attached to the stand to offer any meaningful resistance to pump shake that would result in the pump falling off its stand.A more effective means would simply be to zip tie the stand to the area between the discharge port and the motor body on the pump.Other stands that cost less than half what Zoeller charges for this stand are actually more robust.I do think that a sump pump stand—even this mediocre one--will potentially be more stable and allow better/cleaner water flow to the pump’s intake port than will a couple of bricks.
Chris Winter
2025-04-26 11:43:30
My house’s sump pump was way past its prime, so I researched the crap out of the sump pump market, and bought this stand as part of my new setup.The stand is made from robust black ABS plastic, and is sturdy. It’s a breeze to put together, and I’m pretty happy with the result since it feels a bit more professional than setting my sump pump on a brick. The stand elevated the sump pump by about two and a half inches, but the stand can be further elevated as described in the instructions by fitting some plastic pipe around its legs. The bottom of the stand has holes in it to allow water to flow through to the pump, and also serves as a filter for any debris larger than about 3/4 of an inch.So far so good. I can recommend this product!
the_shining_85
2025-04-04 21:07:12
Used for my Zoeller 3/4 hp sump pump, worked excellent and keeps my pump slightly off the ground, while providing a good base. You can add pieces of 2" pipe to the three bottom foot mounts if you want it to sit higher off the bottom.
Shep
2025-03-09 17:13:13
The stand is solid and made out of a very durable plastic. There are no instructions on how the unit goes together, however it is not hard to figure out. The only hard part is using a screw driver to attach the self taping screw. Once done it is great.
Ma Gra
2025-02-02 14:03:21
Le vendeur n’a aucun mode de retour. Le transport est a tes frais
Recommended Products
$22.28
$ 9 .99 $9.99