Your cart is empty.
Your cart is empty.Product Description
Tahikem 4 Set Black Leveling Feet
It can help you adjust and level your tables, cabinets, workbenches, chair, bookcases, etc. It can solve the trouble of shaking furniture and save money, why not try it?
Non-Slip Pads
We have non-slip feet at the bottom of each furniture leg to protect your floor and reduce noise from moving.
Excellent Qualit
It supports 100 lbs / 45kg of load (with a 400 lbs / 180kg total capacityfor all four black furniture levelers)
Height Adjustment
You can use a wrench to fine-tune the height of each furniture levelers until the horizontal line of the furniture reaches the height you want.
Note: Avoid Wood Cracking
Use a small diameter drill to start drilling, and then switch to a drill size that fits the product.
Installation Steps
Step 1
1.Mark the height on the drill bit with tape, the recommended height is 2 inch/5cm.
Step 2
2.Use an electric drill to drill a hole at the place to be installed, the recommended hole width is 1/2 inch(13mm).
Step 3
3.Put the T-nut into the hole with a hammer and keep it level.
Step 4
4.Finally, tighten the fixing nut and the levelers to complete the installation.
Jack
2025-08-10 13:25:55
These leveler are very sturdy and easy to install. Select the height desired, tighten the nut on the shaft to the housing, and you have a stable foot. The pads included offer extra floor protection.
Came broken
2025-07-09 12:24:26
Really good product, the best option if you have a really bad floor, grat quality, easy to install, easy to adjust , simply perfect product, I highly recommend it if you need it,
J. Whiting
2025-06-20 13:44:21
I have a simple black piano bench that was 1.5-2" too low and these made an effective, affordable, and relatively good looking extension to the legs. This spared me from spending $150-300 on an adjustable piano bench. It comes with matching felt pads if you prefer the feet to slide more softly on the floor.I would be very wary of a device like this for angled legs (this version doesn't support that because the feet don't swivel but even if they did, I would worry the forces involved in anything but purely downward force could result in the wood splitting.)Drilling the holes is the hard part. For a 1/2" hole, I needed three stages. First a pilot hole of around 1/8", then a large diameter 3/8" hole to widen that up, then the final 1/2" hole. Most drill bit kits don't include 1/2" bits so I had to buy one, which cost $11 on top of this kit. Drilling straight down into the leg is important, and you've got to go about 2" deep as that's the length of these bolts, so use a drill with a level guide for this purpose if possible. The minimum drill depth for these to work at all is about 1", which is the depth of the 1/2" diameter insert that the bolt threads into. But at this depth only, the whole bolt won't thread in and you'll be unable to use the whole range of the device, so go the whole 2". But you don't have to make the 1/2" hole a full 2" deep - you can have the intermediate 3/8" hole be the deep one because the bolt alone fits in a 3/8" hole.
Kevin Frank
2025-06-19 10:37:08
These were the perfect part for my DIY project. Large feet, thread adjustment, solid anchor. The back was perfect match for our black stained furniture.
Shawn
2025-04-08 18:58:39
I purchased these adjustable feet for a custom workstation that I made with legs using simple sanded 4x4s. It set it off giving it a floating appearance without making it look jerry rigged for a jerryriggedproject. Excellent product that performed as advertised with the bonus of appearance. My desk is satin black and these blend In very well. Highly recommended.
Ktypdn
2025-03-14 14:28:56
We installed new vanity and wanted to elevate it to cover halls in the wall from old vanity. It worked well. It was easy to level vanity with use of them. Good quality, sturdy.
Vicki Urban
2025-02-27 14:01:41
We purchased a used wine fridge off of marketplace that didn't have feet. These fit perfectly. I couldn't see anywhere where the thread count was mentioned. Only the diameter of 10 millimeters. So I took a chance and ordered them anyway. This is the diameter and thread count,10MM-1.5The last picture is my thread checker. Not part of this kit.
Stephen Mok
2025-02-16 12:39:01
These are quality made swivel levelling feet. Purchased for my hardwood work stool for the garage that is not as level as i liked. Loved that they are of all metal construction. Came with both felt and rubber stick-on pads to use if your furniture needs to slide or if you need it to grip. As per included instruction, i used a 1/2†drill bit and drill a 2†deep hole for the T nut center of legs. All went well. Issue arose when i tapped in the T-nut that i was disappointed. Spikes at the base of T-nuts were too agressive. Too thick. The width of the skewed legs of stool were 1.5†x 1.5†apparently i think you should only use this hardware for nothing under 2â€x2†. Of course no where did it say that in the description prior to purchase. When i lightly tapped the T- nuts in, it split the wood on All 4 hardwood legs , no matter how careful i was tapping them in, after the first, so be fore warned. Now i need wood glue.
Sebastien O.
2025-02-13 16:53:35
Really nice product, would recommand
Robert h.
2025-02-08 18:12:01
These are fantastic. I was looking for some leveling feet for a few work benches that I'm building. I was amazed how strong they are. I have bought quite a few packs for future projects. Would definitely buy again
MR Terence Mason
2025-02-01 14:04:24
I used these to raise the height ot a heavy table after a bit of upcycling. Apart from also needing to purchase a 13mm drill bit, all went perfectly. Really easy to use and great value. Certainly recommend
MMC
2025-01-18 18:44:50
Easy to install. I used a dowel drill guide to drill the holes just to make sure the holes were straight as the chair legs are slightly angled (3-5 degrees) off-centre.T-nuts were easy to hammer in and the threaded feet screwed in smoothly.Used a 1" forstner bit to bore 2mm so the t-nut would be flush with the bottom of each leg.Excellent angled leg levellers for uneven floors. Highly recommended, would buy again
Ben
2025-01-13 18:06:27
It arrived quickly and mechanically works perfect
Recommended Products
$39.99
$ 20 .99 $20.99