Your cart is empty.
Your cart is empty.The CURT anti-rattle hitch clamp helps ensure a quieter ride when towing your trailer. It quickly and easily clamps over the receiver hitch connection to stop rattling, vibrating and noise. This anti-rattle hitch device is easy to use with no tools required. It has a simple, clamp-style lever that allows for fast, convenient installation. It is also easily adjustable to ensure a snug fit. This anti-rattle hitch kit is designed to fit 2-inch receiver hitches and can be used with both hollow and solid shanks. Warning: Anti-rattle clamp must be used in conjunction with a properly secured hitch pin.
El Dorado Dave
2025-08-07 14:39:43
For years I assumed that a certain amount of hitch rattle and noise was just something you lived with when towing. Not long ago I towed a rental trailer over a couple of hundred miles of very bumpy and curvy roads and it sounded like the trailer was ready to break off. After that experience I went to the internet to research the problem and possible solutions. I quickly discovered that this is a very common problem with a variety of relatively simple hardware solutions. The thing that sold me on the Curt anti-rattle clamp is that it does not require any tools to install or remove. And I can testify that it works as advertised making for a much quieter and relaxing towing experience.It did take me a few minutes on the first use to install it and get it adjusted. After doing it the first time, subsequent installation was much easier and faster. And true to its claim, absolutely no tools are needed. The unit feels heavy duty and solid and I feel like I’ll get a lifetime of quieter towing with it.
Kathy mustain
2025-07-31 17:07:11
had a lot of slop in my receiver and took out all the rattle
peadink
2025-06-24 13:15:22
I purchased 2 of these in November of 2024 thinking they were a great idea. I have a #3000 trailer. The clamps worked great at stopping the hitch rattle but soon began to fail. They required frequent tightening to keep things quiet and the anti friction washer under the overcenter device distorted and became useless. Upon removal and closer inspection the truss bar had distorted (bent). I would look for a steel version with locking nuts instead of the overcenter aluminum type.Update: Contacted the manufacturer and was told the wear was normal and expected which tells me these units are designed to fail requiring consumers to purchase again (planned failure-disposable). Shame on Lippert/Curt for desigining and selling such poor quality items!
James T.
2025-06-09 17:02:54
This product does exactly what is needed.Completely eliminates rattle when using a hitch mounted cargo carrier.The easiest method I have personally found to lock it closed is to have the hitch mounted carrier as close to level as possible and then use a rubber mallet to do the last bit of closing the clasp, ensuring a very snug fit and 100% eliminating rattle.I use the same rubber mallet to pop open the clasp once no longer needed.
blazer
2025-05-29 12:07:41
I like the design but the materials are soft aluminum. You only have so much leverage and I could not get this secure enough that I couldn't make it rattle under force pulling the hitch up and down. There are limits to the mechanical advantage of this design. It would work ok for a bike rack but not a heavy boat trailer. I also had limited space for mounting and had to flip the orientation vertically on this with the lever on the bottom. I wound up buying a replacement 2" hitch that has an expandable core using an allen bolt. More money but way more solid.
Dabeav
2025-05-12 18:26:11
No more rattling, banging of receiver hitch! Great idea!
Roger
2025-04-13 13:24:30
Hitch clamp arrived quickly and as described. Although it didn't work for me, my son uses it on his 2017 Chevy Colorado. I bought this to fit my 2023 Rivian R1t but it did not work. No fault to the hitch clamp itself the R1t has zero clearance between the top of the receiver and the bumper. Probably this fact has no use to most users but I thought it should be mentioned.
Robert Waddell
2025-03-18 10:08:50
This device is very finicky to adjust and the nylon glide pad deteriorates over time. It does require a wrench to get the adjustment just right. The latch is constantly dropping open.
keith chorley
2025-03-14 15:49:43
I wanted an anti-rattle clamp that did not require tools to use, since I remove the towing bracket often when not towing. This is the only one of 50 that has that feature.
Old Tin Toys
2025-02-15 18:06:30
Well was a little skeptical when I bought it thinking it was a gamic. LMAO, it really works. It is worth the money and the time to install. But once you have it set to the vehicle it goes on and off really quick.
Igor Kazagrandi
2025-01-23 11:48:15
Handle being aluminium, rubs on steel every time you put it on and take it off, after only a few times it’s already showing significant signs of wear
Client d'
2024-12-10 10:25:18
conforme à la description
Dale
2024-12-03 16:52:50
This looked great, no tools needed quick release rattle adjustment. But after the first or second use, the zinc plating roughs up, so the clamping mechanism becomes very stiff and annoying to use. And clamp force adjustment is only adjustable via a 360 degree turn of the arm, so it is either too tight to do up without feeling like you'll break it, or loose enough the arm doesn't stay clamped up when the mechanism is closed. I hope they go back to the drawing board with this one, and throw some R&D at it to solve these issues!
Recommended Products
