Your cart is empty.
Your cart is empty.Product Description
Engraving Result
Brushed 500W ER11
Daedalus CNC Spindle
Brushed | Brushed or Brushless | Brushed |
0-12000RPM | Operating Speed | 0-12000RPM |
| | Mach3 control | |
| | PWM Control | |
52MM | Diameter | 52MM |
ER11 | Collet | ER16 |
Brushed | Brushed or Brushless | Brushless |
0-12000RPM | Operating Speed | 0-12000RPM |
| | Mach3 control | |
| | PWM Control | |
52MM | Diameter | 55MM |
ER11 | Collet | ER11 |
- Brushed 500W ER16
- Brushless 500W ER11
Russell
2025-09-03 12:29:55
Exactly what I was looking for.
Kevin B.
2025-08-27 20:00:54
Excellent and quieter than the original spindle/router motor.I specifically got this as I haven't yet figured out mach3 and/or linuxcnc and wanted to ensure I had control over the motor.The previous motor sheared the main shaft and also the controller was getting too hot and going into safety.This one is as described. And the collets appear to work. I only used the 1/8" so far.Took about a half hour to go through everything.You will need to provide a power wire from mains to this. I cut the end off a pc power cable
Tomas
2025-08-05 18:58:28
Product delivered relative fast, without damage, good packed. Kit itself has everything as described, nothing missing. Quality is OK. Most important that motor has no vibrations and makes very little noise. Didn't checked collets yet, but i think they could be OK too.I wish price could be little bit lower, but overall i'm satisfied with product.
VW
2025-07-21 13:32:22
First one blew sparks out, second one works. Return and replacement went extremely well.
Customer
2025-05-17 13:50:04
The media could not be loaded.
Heisenberg
2025-05-10 15:05:55
If you are looking for a 500w spindle for your 3018/3040 or something custom, look no further.If you are currently looking at the rattmmotor 500w spindle skip it, I ordered one of those first and it was DoA, ordered a replacement one and the power supply control board was covered in tar like substance, and as soon as the supply was plugged in it blew my breaker. The wiring was correct as it was the same 3 wire plug I was using for my 300w spindle motor first.This product is packaged beautifully, comes with collets, wire, and terminal ends. Power supply looks great has mach support and it is just overall better in all ways. Spend the extra 20$ and buy this one.
Carlos P
2025-04-07 13:01:13
The system is easy to install. The potentiometer and the PWM make it easy to interface.The only issue is that the motor does not deliver 12000RPM. The maximum speed with the potentiometer fully turned clockwise or 100% PWN is 10500 RPM. (This is the reason for the 3 stars)The system is powered at 120 VAC, and the selector switch is in the correct position.
Les
2025-03-31 15:05:10
I recently purchased the Daedalus CNC Spindle Motor Kit, 500W to upgrade my Genmitsu 4040 Reno, and I’m thoroughly impressed with the results. Here's my experience:InstallationWiring up the spindle was incredibly easy. The kit comes with clear instructions, and everything fit seamlessly with my existing setup. Even for someone with minimal electrical experience, the installation process was straightforward and stress-free.PerformanceThe performance improvement over the original spindle is remarkable. The extra speed and power provided by the 500W motor have enabled me to:Use a much wider selection of bits.Cut through tougher materials with ease.Achieve smoother finishes on projects.EfficiencyOne of the most noticeable benefits is the time saved on projects. With the increased power, I’m able to complete jobs significantly faster without compromising on precision or quality. This upgrade has genuinely transformed the efficiency of my workflow.Important ConsiderationKeep in mind that you will need a relay to control the spindle within the software. Without it, you must manually turn the spindle on and off using the speed control dial, which can be less convenient during operation.Overall ImpressionThe Daedalus CNC Spindle Motor Kit is a fantastic upgrade for anyone looking to boost the capabilities of their CNC machine. The combination of easy installation, enhanced performance, and improved efficiency makes it well worth the investment.If you’re considering an upgrade for your Genmitsu 4040 Reno or any other compatible CNC, I highly recommend this spindle kit. It’s a game-changer!
Nelson
2025-02-11 11:33:40
Llego muy rapido, totalmente satisfecho vino de regalo Un collet extra (12 total) y Unas pinzas las cuales no decia qué llevaba, lo acabo de probar y Todo a la perfection la recomiendo.
Riripredusol
2025-01-30 17:39:29
The media could not be loaded.
Sandra Wirkner
2024-12-14 10:36:42
Macht einen guten Job
Andrew
2024-12-03 21:17:00
This was a warehouse item at reduced cost. It came in original box, has all the heatsink and crimp terminals. Has the PSU, working. Has the spindle motor, working. Comes with a 10mm collet installed in the mount. Comes with the motor mount and 4 bolts (won't be using as my CNC already has a suitable mount). Comes with the small reel of cable (won't be using).The only issue I've found (so far) is the shrink wrap on the collect set was open and although there is a 10mm 'unopened' collet in the pack, meaning I have two, there is no sign of the 4mm collet :(Given the reduced cost, I can't complain if thats all thats missing given they are easy enough to get, and buying just the PSU or the motor on their own would cost more than I paid for the whole kit.
Recommended Products