Your cart is empty.
Your cart is empty.
High quality wood veneer edge banding
Wood edge banding is used to cover the exposed sides of materials such as particle board, plywood, metal or MDF. The veneer edging increases the durability of your project as well as giving it a perfect finish.
Real red oak wood pre-glued edge banding
Our red oak wood edge banding is pre-glued with a German high-quality adhesive that provides a strong, permanent bond. The glue is activated by heat and will strongly apply this high-quality veneer edging onto your shelf, furniture or DIY project. You will receive 1 roll of red oak wood, iron-on veneer edging with your purchase.
Easy to install plywood edge banding
The only tool you need to apply this veneer edging is a regular household iron at cotton (hot) temperature. To apply, simply position the veneer edging on the edge of your plywood or other substrate and smooth it with a few passes of an iron. Bandings are impregnated with a high-speed hot-melt glue that creates a permanent, durable bond.
How to apply Edge Supply Edging
1. Prepare Surface Edge:
Fill any large holes, sand rough spots, remove sawdust, cut edging ½" longer than surface to be covered.
2. Apply Edging:
Preheat iron on “cotton” setting, position edging, slowly press iron over edging, check to see if glue is melting. Note: Use kraft paper or aluminum foil to protect iron bottom.
3. Bonding:
While still hot, press veneer down firmly with wood block or roller, If there is a mistake, simply reheat and reapply.
4. Trim Edge:
Allow edging to cool completely, trim any excess with an edge trimmer, a razor blade or file, sand smooth and finish as desired.
BUY NOW this premium quality, red oak iron-on wood veneer edging
Customer
2025-07-30 18:13:54
This edging worked great on the island we built. It stained nicely, sealed really well and put the perfect finishing touch on the top!
KingOfCats
2025-07-19 15:48:40
Have purchased this multiple times. Works very well. Will continue to purchase as long as they don't hike the price up.
EV_Sea
2025-06-24 12:32:34
Great adhesion when properly applied and perfect color match to the red oak ply I bought at our local lumber store. Made custom built in bookshelves.Only complaint is the branding sticker used leaves a sticky residue that stains the wood. I had to cut off about six inches and toss off the beginning of the roll and it just happened that I was short that amount for my project.
Anne S
2025-06-23 14:18:42
I loved this edge banding. I applied it with an iron and pressed it down with a wood block. I didn’t have any issues with it lifting or with the glue coming off. It was just slightly wider than my 3/4 in plywood which was nice because that made it easier to apply. I trimmed the excess with a utility blade. I went nice and slow and had no problems. It stained well and matched my plywood perfectly. Highly recommend
Customer
2025-06-17 10:13:40
Easy to install and stain. Looks great!
Tom
2025-04-21 13:26:53
Came a day early. I was skeptical about the adhesion system, but so far, with some experimenting, it seems to be adhering good.
m. cirineo
2025-02-12 12:45:50
Ordered .75" and 1.5" widths. The 3/4" was dead nuts on. The 1-1/2" was 1.375". Maybe Amazon stock is screwed up or maybe supplier sliced it wrong or listed the wrong width. Anyways, it's wrong and holding up my project, thus 1 star. I'm returning this one and ordering another. If still wrong, I'll post an update and buy it somewhere else.Update: The reordered size was correct. Additionally the mfgr reached out and offered to send a replacement for free. I don't need the free roll, but the gesture to correct the issue was appreciated. Plus the stuff really looks and works great. I changed the rating to five stars.
Blue
2025-01-17 11:43:24
The product does what it should do but be very careful making sure it's fully adhered. I found there are times adhered spots will pop-up and need to be ironed a second time. Make sure you have a rubber roller as well, ironing alone won't get the job done.
Freddy228
2025-01-14 12:13:47
Seeing that I am from Australia and the edging comes from the US, it matched the Red Oak plywood perfectly.
Recommended Products
