Your cart is empty.
Your cart is empty.
Jin&Bao LED CONNECTORS ELECTRIC ITEMS
The connectors apply to 4-Pin 5050 RGB LED SMD Light Strip.
- Applicable light strip width: 10mm(0.39inch)
- Applicable light strip thickness: 0.3mm-0.4mm
- Applicable lines range: AWG22#/20#
- Current: 5A, AC, DC
- Voltage: DC 12-24V
- Working temperature: -40℃ +105℃
- Breakdown voltage: 1500V, AC/min
- Contact resistance: 30mΩMAX
- Insulation resistance: 1000mΩMIN
- Product bite traction: >12N
Product Material
- Housing: Nylon 66UL94V-0
- Contact: Over brass tin
【CONNECTOR INSTRUCTIONS】
- Ensure your light strips work well.
- Cut along the suggested line of the LED strip evenly.
- when used for waterproof LED strips, please strip the silicone on the contact area (about 0.25inch).
- Align the "+" on the light strip with the side with the cover on the connector. Ignore the RGB/BGR labels, which are irrelevant.
- Slide the LED strips to the connector from the slots on the connector sides.
- Make sure that each metal pin on the connector is pressed above the brass contact point of the light strip.
- Turn on the power to make sure that each LED is working. Then close the lids of connectors.
Customer
2025-06-01 14:09:52
Made my install easy quality good if you are going to make it fit properly for the coners highly recommend fit properly
GB
2025-05-27 12:08:31
Hate turning on the lights at 3am and being blinded and not being able to go back to sleep. You also don't want to piss off your gf and piss all over the seat since you can't see? Than get this lol its perfect at night for going to the bathroom and all my friends get a kick out of it.
ADAM CARTER
2025-05-10 13:01:43
I’ll be honest. These didn’t work for me. But it was my fault. I’m reviewing, more based on the visual location.They look like they’re made well. Was able to open and close the connectors pretty easily. Felt sturdy. There is also a good variety of parts, which is helpful.The mistake I made is that these are mean for 10mm light strips. My Govee lights are 8mm. So the strips don’t line up with the electrical nodes to make a circuit. Now I need to go back and order different 8mm connectors.Lesson: be sure to check if your light strips are 8mm vs 10mm!
Jason
2025-04-28 15:47:18
Cheaper than anywhere else we found even Wal Mart & more lights. Son loves them & they went around his 14.8x14.8 room at the top, down the edges, around the bottom, & even around his bed! Couldn’t have been happier! They’ve been on over a year & still work the same as the day we put them up, well made, & have never had any issues with them working exactly as described! GREAT PURCHASE!!!
Matty
2025-04-27 12:17:45
Kit came with everything you need. But the led strip I was using it on has the clear rubber over the strip itself. It took me many tries to remove the rubber without damaging the connection points. After finally getting a good clean strip without any obstructions, the RGB strip only lights up with shades of green now. Even tried to cut strip again and achieve clean open connections, yet still only get green colors. The strip after the connection doesn’t light up after connector.Number of contact points is the same in the connector as in the led strip so I gave up and accepted only green shades for that section of strip (48†strip kit, 2-24†strips).Overall kit quality is good. I would recommend it as long as you know the connectors work with your led strips
Customer
2025-03-24 17:49:31
Experienced in electronics here, I can honestly say this product is garbage and DOES NOT maintain a proper electrical connection. Even if you finally think you've got it working, you'll eventually notice your lights randomly go out, or display uneven colors and brightness between each segment. Some connection segments are so bad they even cause entire colors to go out. This is because the cheap contacts don't allow consistent and proper current to flow between all 4 contacts throughout your entire strip.It was very odd because upon close inspection it appeared the connectors dug in deeply into the copper pads and appeared to have a firm contact. Yet despite this, they still would randomly fail. I verified these issues using a current meter. One minute they'd work, the next they'd lose partial or full contact.These cheap connectors caused the current flow to be so wonky and inconsistent that I lost confidence in the product and decided to hand solder them all with homemade jumper wires instead. Now they are 100% bright with all colors through to the very end of each strip.But then to add insult to injury, I couldn't even get the peel-and-stick strip clips to stick to anything longer than 5 minutes. There was nothing in this kit that worked right, so I finally trashed the entire kit and hand soldered all my connections with homemade jumper wires instead; and bought real 3M to stick the clips properly.Further research shows this kit is so bad that there are other manufacturers who use this kit as an example of what NOT to buy. They are quite aware of these cheap connectors being sold and make a much higher quality version in response. They even use these cheap connectors in their ads to do a side-by-side comparison of a cheap connector compared to their quality one. I hope this review spares someone a headache.It's so bad that other manufacturersResearch LED strip soldering on YouTube.
Emily
2025-03-21 14:29:43
Works super great! Perfect!!!!
Jon Lopez
2025-01-30 15:48:25
Nice
Mike
2025-01-24 13:37:56
As specified
Sondra
2024-12-06 12:01:52
It would be nice to get instructions with these since not everyone knows how they work
Alfredo Méndez López
2024-12-04 14:40:31
Excelente producto.
Russell
2024-11-30 10:54:17
Easy to install
Steve G
2024-11-12 10:53:46
Once you figure it out it works great
Recommended Products
