Your cart is empty.
Your cart is empty.Product Description
KOHLER GENUINE PART GP1016515 KITCHEN FAUCET VALVE, White
From the Manufacturer
Kohler Genuine Part, Valve for single control faucets, Valve Kit.
Pappy
2025-08-26 10:11:07
Faucet was leaking around the base. It appeared to have been original to the home so was about 20 years old. Took it apart and found the valve was loose in the housing and was leaking. This valve was a direct replacement and was very easy to install. Works like new and saved me a lot of money and effort over having to replace the faucet.
unotme
2025-08-09 10:45:47
This part fixed a frozen handle on my Kohler single spot faucet. I was convinced I needed a new faucet but when I went on YouTube to see how to install a faucet I came a cross someone showing how to replace valve so I gave it a shot. Hardest part getting cap off that protects valve. Many years of no maintenance had it all gunked up. Once that was off I popped out old frozen valve, replaced o-rings, lubed and popped in the new valve. Works like new and only cost me $18 to fix!!
Jere
2025-07-27 19:32:33
Ordered this to repair my kitchen faucet that was leaking pretty bad from under the handle. Replacement was a breeze. The most difficult part of the repair was loosening the protective cover directly under the faucet handle. Once that was off the larger nut that retains this valve came off easily. The replacement took less than 10 minutes including the time I took to clean up the scale that had accumulated due to my hard well water.
KJL
2025-07-11 12:04:01
Perfect fit, easy repair, and works like it should Also bought the o rings and seals but my faucet did not require them so I returned them.
Dennis
2025-07-10 16:17:21
I needed to fix water leaking around the faucet handle and the replacement cartridge was very easy to install. I decided to also replace the O-rings and bushings while I had the faucet disassembled and recommend replacing those parts, too. If I had to do it again, I'd also replace the spay diverter valve.
RatherLiveInKeyWest
2025-07-06 10:59:35
This valve kit was exactly what we needed to stop a leak in our 2.5 year old Kohler K-10412 Single Control Faucet (Brushed Nickel finish).The leak started about a week ago and got progressively worse each day, virtually turning into a river two days ago. The parts were delivered yesterday and, with our 14 year old son's help, we fixed the leak this morning. The job took about 20 minutes total (think we could do it in 10 next time though...), and we also replaced the o-rings and slide bearings () and the friction ring () in the process.Here is what we did to replace the valve; if looking for the steps to replace all parts mentioned above, please follow the link to the o-ring kit and read the more expansive worklist:* Turned off the water running to the sink* Put stoppers in the drains on both sides of the sink, just to make sure nothing accidentally went down the drain...* Used a small flat-head screwdriver to remove the plug from the back of the handle, providing access the handle's set screw* Used a small hex (Allen) wrench to loosen the set screw, and then lifted the handle off* Unscrewed (by hand) the covering over the valve (took a bit of 'uumph' to get started, but easy thereafter)* Used a pipe wrench to loosen the mounting nut holding the valve in place, then finished loosening and removing by hand* Removed the old valve; the gaskets from the bottom of the valve were stuck inside the faucet, so we had to clean that out* The valve stem sits in a plastic bracket mounted in the handle; we replaced the old bracket with one that came with the valve* Used soap & the Scotch-Brite material to clean the inside of the handle and faucet* Put the new valve unit in place, lining up the posts on the valve to holes inside the faucet for a perfect fit* Cleaned and replaced the mounting nut; hand tightened, then used the pipe wrench for the final quarter-turn* Cleaned and then screwed on (by hand) the covering over the valve until finger tight* Placed the handle back on top of the valve, lining up the valve stem with the new plastic bracket we installed* Put the set screw back in place, and hand tightened with the hex (Allen) wrench until just snug* Replaced the plug covering access to the set screw* Took the drain stoppers out* Turned the water back on... looked for leaks... turned the faucet on and tested the hot & cold water flow... moved the spout aroundNo leaks. Like new. Excellent.Was a lot nicer to spend $20 instead of $200 for a new unit.If you have the same sort of issue and have confirmed that these parts are right for your unit, we recommend them very highly.Go for it.
rocks are people too
2025-06-29 19:12:33
My kitchen faucet had been fussy for quite a while, leaking out the spigot if I didn't close it carefully. I finally ordered this and put it in just now. Leak is gone now.Before I ordered I watched the installation video from Kohler (easy to find on YouTube) and took a look at my old valve to make sure it matched and confirm that I had the correct tools. I recommend this step for anyone who is unsure of whether or not to order this as a DIY task.I didn't bother ordering the O rings they suggest installing at the same time. I'm not sure, but I think I only would have needed them if the leak had been around the valve instead of through the valve and out the spigot.
George S.
2025-05-15 15:02:35
Fixed the leak. Faucet is like new again. Highly recommend. If you call them Kohler will replace the parts for free. Or if out of production replace the faucet. I found this out AFTER, I repaired mine. So just a heads up.
Soupy Dave
2025-05-04 13:12:55
Excellent replacement part for a 15+ year old faucet
MaggieMaySeller
2025-04-02 16:17:57
The tap was leaking and it turned out to be the internal cartridge needed replacing.
Jeff-B. - Okanagan
2025-03-15 14:48:08
Easy to replace (if you know how to disassemble your Kohler faucet). Seems to work fine. But, on occasion, the faucet sometimes makes a "clunk" noise when the tap lever is turned on. Not sure why that happens. But, otherwise works ok.P.S. Be sure to always replace your faucet "O" ring set at the same time. I have to replace my 0-rings every few years it seems like.
Jacques
2025-02-06 11:32:53
Excellent rapport qualité/prix, produit authentique Kohler, remplacement facile de la pièce originale. Mais il faut absolument avoir de la graisse de silicone pour le remontage afin que ça glisse facilement. S'assurer également de bien nettoyer les dépôts calcaires dans le compartiment de laiton dans lequel cette cartouche s'insère si on veut un fonctionnement aussi doux et efficace que l'original. Faire couler du vinaigre blanc dans le compartiment, att3ndre une 30 de minutes puis un petit coup de brosse, on assèche, on dépose un peu de graisse et ce sera comme neuf.
N David
2025-01-21 11:25:33
I initially received an open package from Amazon with a valve that was installed by someone, but Amazon replaced it without issue. I have a 10 year old single spout stainless Kohler kitchen faucet that began to leak for the 2nd time. The valve and o-rings were easy to install and fixed the leak I was having from the base of the unit. The toughest part was removing the decorative cap which was seized on. I cleaned the faucet with CLR and alcohol before reinstall. For the price of the kit, it was worth repairing versus replacing the faucet.
Recommended Products
$100.00
$ 43 .99 $43.99