Shopping Cart

Your cart is empty.

Your cart is empty.

Moroso 64920 Carb Linkage Bushing Kit

4.8 (20) Write Review
Free shipping on orders over $29.99

$14.99

$ 7 .99 $7.99

In Stock
  • Split bushing design permits simple installation and eliminates the sloppiness present when rubber bushings are used
  • Clear zinc finish
  • Country of Origin : China
  • Fit Type: Vehicle Specific


BUSHING KIT, CARB LINKAGE


TWyckoff
2025-08-28 17:11:07
I installed this bushing set on a Holley 3110 in order to adapt the big hole in the carburetor linkage to the mechanical throttle linkage on my 59 GMC. The bushing is of very high quality and it is made in America. I did have to mill approximately .020 off one side of the bushing in order to properly space my linkage, but that is more the fault of my linkage setup - not the bushing. The anodized finish looks nice and should provide some corrosion resistance. Good quality part.
Agent J
2025-07-31 13:16:41
Used this for throttle linkage on my Edelbrock 1404 (same difference as 1406, etc) it fit the hole perfect and it’s just a couple bucks more than those plastic and rubber ones. Highly recommended.
Mike vickroy
2025-07-29 13:41:11
It works great on my Holley carb
Jim
2025-07-16 14:59:45
Worth the money. Good product.
Chuck R.
2025-07-11 15:36:02
I like fitment, I used it to connect my throttle rod to my carburetor.
R. Gioia
2025-07-01 10:55:15
This product worked as advertised. Excellent quality!
Skyler
2025-06-24 10:54:50
Perfect works awesome on my eldebrock carb much better than the rubber grommet set up
RagenRat
2025-06-22 15:21:25
Moroso 64920 Carburetor Linkage Bushing SetThese look and feel great, they fit right in the throttle lever hole on my Holley & Demon carburetors and there was no looking back.I have used other Moroso Products many times before and have been very happy with them, this one is added to one of my best. :-)Buy with confidence.RagenRat / Mark
TWyckoff
2025-06-09 17:38:01
I installed this bushing set on a Holley 3110 in order to adapt the big hole in the carburetor linkage to the mechanical throttle linkage on my 59 GMC. The bushing is of very high quality and it is made in America. I did have to mill approximately .020 off one side of the bushing in order to properly space my linkage, but that is more the fault of my linkage setup - not the bushing. The anodized finish looks nice and should provide some corrosion resistance. Good quality part.
Agent J
2025-05-28 11:58:45
Used this for throttle linkage on my Edelbrock 1404 (same difference as 1406, etc) it fit the hole perfect and it’s just a couple bucks more than those plastic and rubber ones. Highly recommended.
Mike vickroy
2025-05-12 14:26:01
It works great on my Holley carb
Jim
2025-05-10 12:16:02
Worth the money. Good product.
Chuck R.
2025-04-23 14:13:18
I like fitment, I used it to connect my throttle rod to my carburetor.
R. Gioia
2025-04-04 11:51:05
This product worked as advertised. Excellent quality!
Skyler
2025-03-27 16:47:04
Perfect works awesome on my eldebrock carb much better than the rubber grommet set up
RagenRat
2025-03-25 17:21:38
Moroso 64920 Carburetor Linkage Bushing SetThese look and feel great, they fit right in the throttle lever hole on my Holley & Demon carburetors and there was no looking back.I have used other Moroso Products many times before and have been very happy with them, this one is added to one of my best. :-)Buy with confidence.RagenRat / Mark
Jorge Carbajal
2025-03-22 09:32:46
Lo use para un carburador quadrajet en un motor oldsmobile, solo usé la parte más angosta y aumenté el diámetro del cable del acelerador con un dremel para que entrara. Ya no hay juego en el pedal del acelerador y se mueve muy bien!I used it for a quadrajet carb on an oldsmobile engine, just used the narrowest part and increased the diameter of the throttle cable to fit. There is no play on the accelerator pedal and it moves very well!
Ironleg
2025-02-27 16:42:38
Nice fit but expensive.
Jorge Carbajal
2025-01-20 10:46:34
Lo use para un carburador quadrajet en un motor oldsmobile, solo usé la parte más angosta y aumenté el diámetro del cable del acelerador con un dremel para que entrara. Ya no hay juego en el pedal del acelerador y se mueve muy bien!I used it for a quadrajet carb on an oldsmobile engine, just used the narrowest part and increased the diameter of the throttle cable to fit. There is no play on the accelerator pedal and it moves very well!
Ironleg
2025-01-14 17:58:04
Nice fit but expensive.