Your cart is empty.
Your cart is empty.
Features:
Size: 8 Inch
Material: High Carbon Steel
Surface Treatment: Heat treatment
Number of Claws: Two-claw
Type: Claw Puller
Product Name: 8 Inch Carbon Steel Pump Pulley Remover
Size: 8inch
Screw length: 180mm
Screw diameter: 8mm
Cross arm length: 115mm
Total claw arm length: 160mm
Maximum depth distance of reach: 150mm
Internal pull diameter(adjustable)：20-85.5mm
External pull diameter(adjustable)：38-94mm
Product Weight : 700 G / 24.69 Ounces
Product Dimensions (L*W*H) : 195*120*30 MM / 7.68*4.72*1.18 Inches
Package Include:
1 x 8 Inch Two Claw Puller
Devil's Hand Diesel
2025-09-03 11:13:54
Great quality, cheap price, easy to use, somewhat durable, great size, great appearance.I used it to pull bearings in my Toyota transfer case. I couldn't get under the bearing but I was able to grab the lip of the bearing where a c clip goes. Worked great but it did bend slightly. In all fairness the book said I needed to apply heat to remove the bearings and I did not apply heat. That's a cold pull.A 14mm impact did the trick on this thing. My only complaint is that it bent, but that was a tough pull.
A. P. Boston
2025-08-30 12:41:09
Nothing
Gary V.
2025-07-05 10:32:15
Worked no issues. Few screw caps of different diameter would been a big help. But that’s what you pay.
Nashoba Losa
2025-06-11 11:50:49
This OriGlam Two Jaws Bearing Puller/Remover, Adjustable Two Jaw Puller and Bearing Puller looks like what I wanted to pull a rubber seal when I am changing out a drive shaft center carrier bearing unit from my truck because the seal is worn out and needs to be replaced. The "jaws" are plenty long and the hooks are sharp enough so the task should be relatively easy with this unit. It appears to be more than strong enough and the cost was acceptable so this relatively limited-use tool should last me a long time.
L and G Hollingsworth
2025-05-26 12:48:52
This puller is not a heavy duty unit but it is strong enough to pull bearings that have a light press fit. It's jaws are thin enough to fit in tight places. I used it to remove bearings from Campagnolo Ultra-torque cranks on my road bicycle. It did the job just fine. I used a wood block to protect the crank end. The puller that Park Tool sells (CBP-8) for the same job costs $108, this one is $20 and does the same job.
22 Acacia Avenue
2025-05-09 12:42:01
Bought it to pull an armature bearing , puller bent.
Charlied
2025-04-24 18:06:49
I have used only once and it works great for replacing bearings and yard equipment !!!!
Aaron Brighton
2025-04-20 13:21:37
I fought a seized bearing in an electric motor for far too long. Bought this and had it off in 5 minutes. Built well so it will last a long time.
johnjohn105
2025-04-04 12:27:39
easy to use and good quality. removed a seised snowblower pulley bearing from the shaft. there is not enough space for other tools. this one worked very swell for this purpose.
Roberto Ochoa Gutiérrez
2025-03-21 14:05:58
Yo lo compré para extraer poleas de bicicleta, si me funcionó. Es de un material bastante solido pesado.
Joe narzisi
2025-03-11 17:13:19
HAVE USED MANY TIME ALREADY AND WORKED VERY WELL
Johnny Lunchbucket
2024-12-07 16:05:01
Bought this for use when overhauling my automatic transmission. It's cheap and it worked. Just what I needed because I doubt I'll ever use it again!
ML
2024-11-26 10:03:35
A bit janky - followed the advice of another buyer to lose the weak pin (it lost itself actually) and clamp the tongs together and it worked ok for some lightweight separation of a stuck NSF post from a shelf. Wouldn't try it for much more than that tbh.
Recommended Products
$27.99
$ 13 .99 $13.99